Mar 27 2024 Release Version 3.29 ====================================== Systems: - [Engines] Improved G/A thrust mode logic - [Engines] Fixed missing N1 trend in some conditions - [Engines][Professional] Fixed hung start fault - [GPWS] Added update threshold to modulation - [GPWS] Add GPWC modulation database state to UI treenode - [GPWS] Feed GPWC with destination airport and runway to minimize nuisance alerts - [GPWS] Added debug info to help debug GPWC related issues (http://127.0.0.1:8080/gpwc) - [FMS][PAR-9830] Fixed speed constraint type not shown - [FMS][PM-46] Improved RAD/FIX data entry and rendering - [FMS][FIX] Fixed SEL DESIRED XXXXX order when no route entered - [FMS] Improved V SPEEDS UNAVAILABLE message - [FMS][PROSIM737-240] Fixed LOC CAP ACTIVE message showing without APP mode armed - [FMS][PAR-9864] Do not merge waypoints if previous one is a hold - [VNAV] Fixed speed restrictions not complied during takeoff/climb below FL100 - [VNAV][PAR-7726] Fixed target speed error below default speed/alt restriction in some conditions - [Autoflight] Link A/T to left RA only - [Navigation][Professional] Added RA partial failure Note: this failure will make RA to return ground level reading - [Autoflight][Professional] Fixed unreliable airspeed failure not cascading to A/T - [Anti ice] Added OFF/AUTO as anti ice hardware option - [Engines] Removed internal start valve dummy failure Note: This will remove the empty button in ProSimIOS failures page - [PROSIMA320-764] Add header support to AOCMessage - [Datalink] Added FROM station to RCVD MSGS page - [Datalink] RCVD MSGS page will now refresh if new uplink is received - [Fire protection] Fixed pulling fire handle not shutting down engine Drivers: - [Flight Illusion] Fixed backlight not turning off for compound gauges - [FDS] Improved FDS Ethernet driver to better support new devices Displays: - [Displays][PAR-9755] Fixed ADIRU VS data source - [Displays] Fixed overlap of heading box and TCAS rings in CTR mode with range 5 - [Displays] Fixed overlap of FROM/TO and TCAS rings in CTR mode with range 5 - [Displays] Fixed TCAS indications on ND should calculate alt delta based on pressure altitude instead of indicated altitude Misc: - [ProSimIOS] Fixed reset cloud base altitude when changing precipitation in custom weather - [Misc] Added possibility to override flight control axis in SDK driver - [Misc] Fixed engine starting state in non starting conditions Note: This fixes the speed stuck at 230kt - [PROSIM737-238] Streamline / cleanup UI menus - [PROSIM737-238] Hide "Import from V2" if config.xml file is already present - [HUD][PAR-9810] Fixed FMA order - [Misc][Professional] Fixed SID parsing when using LIDO database Feb 01 2024 Release Version 3.28 ====================================== Systems: - [Autoflight] Code optimization - [Autoflight] Added power transient protection to yaw damper - [Autoflight][PAR-9458] Fixed approach mode armed logic - [Autoflight] New yaw damper logic Note: YD completely redone with both channels and WTRIS [Professional] - Added yaw damper failure - Added yaw damper CBs [QTG] New yaw damper is disabled by default as it will require a re-run of MQTG Added temporary cockpit setup option to enable new yaw damper - [FMS] Fixed ALT CONSTRAINT nnnnn not returning first waypoint - [FMS][LEGS] Fixed CDU crash when adding first waypoint if no destination entered - [FMS][LEGS] Fixed INTC CRS rounding - [Datalink] Added Generic ATIS provider Note: It is now possible to have ProSim generated ATIS (Voice and Datalink). Please read more info in wiki: https://wiki.prosim-ar.com/index.php/Communications - [Datalink][Printer] Fixed not available variables not cleared from print output - [Datalink][Templating] Added parameters to timeStamp Note: Added UTC and FORMAT parameters (if not present, previous defaults are used) e.g.{timeStamp:format=ddMMM HHmm:utc} - [Datalink] Added extra log to hoppie poll errors - [Datalink] Updated default online weather end point - [Datalink] Fixed CPDLC host not initialized - [Datalink] Added PRINT prompt to clearances - [Datalink] Fixed ATC/ATS message pagination - [Engines][SW-187] Added TR [N] interlock retract signal - [Navigation][GPWS][SW-189] Added GPWS short test - [Oxygen] Added Oxy test switches for CAPT and FO - [Oxygen][Commercial] Added Oxy test switch for OBS - [Electrical] Fixed EPC logic when removing GND PWR - [Electrical] EPC implemented as contactor instead of breaker - [Electrical] Revised BPCU logic - [Communications] Added voice ATIS capability (new cockpit setup in Audio section) - [Communications][Simconnect][SW-134] Prevent frequency values set to ZERO if simulator is not in ready state - [Communications] Fixed navdata frequencies missing last digit - [Communications] Fixed squelch if tuned frequency has no active signal - [Communications] Added workaround to handle Navigraph frequencies not in 833 spacing Note: If using Navigraph, it is required that NavData.dat and NavData_Stby.dat files are deleted from the ProgramData\ProSim-AR\Navdata folder - [Communications] Added glareshield mic push button element - [Communications] Added SATCOM IO elements Note: There is no SATCOM system. This is only available for hardware support. - [Flight controls][Control loading] Added additional datarefs for Brunner control - [Engines] Engine start refactored - [Engines][Commercial][PROSIM737-235] Fixed missing start limit and fixed ENG FAIL flag when start valve is open for HOT START fault - [Engines][Commercial][PROSIM737-236] Fixed static hung start EGT - [Engines][Commercial][PROSIM737-235] Added ground protection to hot start fault Drivers: - [Sismo] Added SATCOM mappings - [Phidgets] Updated library to 1.17.20231004 - [CPFlight] Added support for new ACP panel - [CPFlight] Added support for new SIDE panel - [CPFlight][MCP PRO] Prevents AT to arm if not allowed to Displays: - [Displays] Fixed altitude prediction arc in CTR mode - [Displays] Fixed TCAS rings in CTR mode - [Displays] Fixed standalone duct press gauge - [Display][PAR-9515] Fixed flap retraction speed schedule showing current flap setting - [Displays] Added PARKED VREF cockpit setup option Note: ProSim already had this by default. But it was converted to an option so the regular version can also be used If you need the parked VREF with flaps/speed value, just enable this new option. - [Displays][PFD] Improved V speed bugs rendering - [Displays][EICAS][PROSIM737-235] Fixed EGT digits blinking instead of box in case of impending hot start Audio: - [Audio2] Added group facility - [Audio2] Fixed all sounds enabled by default - [Audio] Added new cockpit environment sounds New sounds were added (not enabled by default). They can be enabled in ProSimAudio2 Oxygen mask sounds (flow and test - L, R and OBS) V speeds (V1, VR and V2) Packs (L and R) Airstairs Standby instruments (gyro and vibrator) Hydraulics (electric) Electrical noise Wipers (INT, LOW and FAST - L and R) Cockpit fans Stick shaker (L and R) Trim wheel Misc: - [Misc] Added connected modules section to UI - [Misc] Added addon state as section in main UI status panel - [Misc] Fixed database swap hang - [Misc] Added SID and STAR to xml query output - [QTG] Fixed automatic QTG delay test not working properly Note: please check documentation with extended example and new variables - [Communications][Simconnect][SW-134] Prevent frequency values set to ZERO if simulator is not in ready state - [Misc] Hide RevSim and OtherMCP support in preparation for EoL - [DEV-431] Removal of very old web IOS - [IOS][SW-201] Fixed invalid init bank value - [Misc][Professional] Added cockpit setup option to inhibit automatic ice accumulation - [Misc] Added ICING DETECTED reset condition that can be removed to clear all accumulated ice - [Misc] Removed RevSim and Other MCP support Note: https://forum.prosim-ar.com/viewtopic.php?t=27071 - [Misc][PAR-9615] Parse NN(S|N)NNN(W|E) Waypoint format in route import (Datalink or company routes) to prevent simbrief import errors - [Misc] Added HGS panel display datarefs - [FS2020] Temporarily disable YD law for FS2020 when on ground Note: YD issue with FS2020 is induced by NWS FS2020 issue. When NWS issues are fixed, ground restriction will be removed - [FS2020] Improved altitude handling Note: This will improve altitude reporting on ATC networks - [TIOS] Fix potential memory leak caused by incorrect airport com data - [TIOS] Support scenery items with null com entries - [ATIS] Added support for simulator weather - [Misc] Fixed FMA Thrust gates not working Oct 24 2023 Release Version 3.27 ====================================== [Systems] - [APU] Fixed APU not resuming operation if switch is set back to ON while in cooldown mode - [FMS][FIX] Fixed destination RWY entry not working properly in some conditions - [FMS] Clear exec light just for the executed command - [FMS] Fixed RTE page not refreshing when FMS is reset - [FMS][Commercial][PM-44] removed beta restriction from RTA FMS feature - [FMS][N1 LIMIT] Fixed OAT value not rounded properly - [FMS][PROGRESS][PAR-9054] Fixed negative destination DTG in some conditions - [FMS][Professional] Force snapshot recall to pre-cache procedures - [FMS][Professional] Fixed PERFINIT snapshot recall - [Navigation][SW-172] Fixed exceeded vertical ANP not triggering ND message - [Engines][SW-116] Fixed ENG FAIL flag - [Engines][Professional][SW-116] Fixed severe damage with red line EGT not triggering engine fire indications - [Engines][Commercial] Fixed quick start not working right after shutting down the engine - [Engines] Fixed inflight engine start with start switch in off position or above FL270 - [Engines] Tuned start tables - [Engines][Commercial] Improved high oil temp failure - [Engines][Commercial][PAR-9361] Split severe damage failure in 2 (with and without fire warning) - [Electrical] Fixed GCU auto close after take off - [Electrical] Adjusted GCB/BTB logic - [Electrical] Fixed EPC not tripping when GND PWR removed - [Electrical] Removed main bus failures Note: Main bus failures do not have any visible flight deck effects and it does not make sense to have it - [Autoflight][PAR-9333] AP will now disconnect if the side XFR BUS changes source - [Autoflight][PAR-9096] Limit FD bank to 8 degrees if both RA are failed - [Ice and rain protection][Professional] Added window overheat failures - [ISFD] Added reset condition to remove ISFD initialization instantly - [Fire Protection][SW-110] Fixed overheat condition immediately reset after APU/ENG fire extinguished - [Pressurization][SW-123] Fixed pressurization not reset in some conditions - [Pressurization][SW-123] Fixed MC active after resetting pressure controllers - [Hydraulics][Professional][PAR-9373] Fixed leak failures not resetting reservoir qty - [Datalink] Improved airborne address handlers - [Datalink] Fixed FREE TEXT page duplicating entries - [Datalink] Added option to uplink hoppie errors - [Datalink] Added Oceanic clearance request - [Datalink] Improved advisories logic - [Datalink] Fixed received messages header - [Datalink] Fixed page navigation after sending a message - [Datalink] Improved PDC/CLD support Note: For vatsim/hoppie users, when requesting PDC/CLD, request is sent as telex, but answer will be in CPDLC format requiring CPDLC to be logged on, causing issues with the controller. With this version, all CPDLC type messages sent from any station other than the one we are currently logged on, will be handled as standalone CPDLC messages and will be avail under ATS->ATS LOG - [Datalink] Simbrief provider now sends all fuel and weight values to the template - [Datalink] Added BLOCK fuel to template [Displays] - [ProSimDisplay] Added CDU screen - [Displays][PFD][PSDB-490] Improved VREF render - [Displays][PEI] Fixed EGT gauge when EEC not active. - [Displays][HUD] Fixed VREF position - [Displays][VSD] Fixed green aircraft symbol [Drivers] - [Simworld][Professional][SW-137] Improved circuit breaker reset - [Poldragonet] Fixed LE Devices mappings [Audio] - [ProSim Audio 2][SW-166] Fixed gates for addons not refreshing at startup - [ProSim Audio 2] Fixed morse code not working - [ProSim Audio 2][DEV-430] Fixed AudioProvider lock [Misc] - [ProSimIOS] Restrict Gate/Parking list to relevant options - [ProSimIOS] Trim reset now also resets aileron trim - [ProSimIOS] Fixed approach statistics is not automatically reset when positioning aircraft on approach - [ProSimIOS] CG diagram turns now red when outside of flight CG limits - [ProSimIOS] Added some extra exception handling for real-time weather METAR updates - [ProSimIOS][Commercial] Fixed FMS snapshot was not re-loaded when resetting current flight situation - [ProSimIOS][Professional] CPDLC ATC name and unit are persistent now - [ProSimIOS][Professional] AOC address is now used from ProSimSystem datalink configuration - [Misc] Fixed invalid altitude(not rounded to hundreds) set to MCP after reposition - [Misc] Fixed potential issue if no FD is active and aircraft is on ILS - [Misc] Make legacy radios and 833 option exclusive - [Misc] Corrected ATA 32 chapter names - [Misc] Combine engine failures under ATA-71 - [Misc] Fixed P3D V6 DB rebuild issue - [Misc] Engines will now start if ProSim is set in ready mode - [Misc][SW-124] Sync analog radio element with the actual frequency - [Misc][SW-135] Immediately refresh TCAS table when removing all intruders - [Misc][SW-139] Make ND and FMC wind to be related to TRUE to match IOS - [Misc][SW-152] Reset GA mode after reposition - [Misc][SW-160] Added SLEW to PFD sim state - [Misc][Professional][SW-140] Added option to adjust indicated altitude for density(temperature) - [Misc] Fixed display issue of WEB IOS with Windows display scaling enabled - [SimConnect][SW-120] Fixed ISFD barometric adjustment not working - [SimConnect][SW-158] Fixed weather radar not working when Active Sky is not used - [SimConnect][SW-165] Fixed internal ASP not resetting NAV channels - [SDK][QTG] Added calculated gross thrust dataref - [SDK] Expose airline data and aircraft tail number as datarefs - [SDK] Added CDU screen content datarefs - [Database] Several small improvements to the backend Aug 4 2023 Release Version 3.26 ====================================== Systems - [Electrical] Basic system overhaul (Tie Bus, BTBs, GCBs, EPC & APC added as active elements) - [Electrical] Improved TR UNIT signal - [Electrical] Fixed DC bus tie relay not opening when GS captured - [Electrical] Added TR3 XFR relay as element - [Electrical][Professional] Added BTBs failures - [Electrical][Professional] Added EPC failures - [Autoflight] Fixed MCP speed limited to barber pole - [Autoflight] Fixed bank inputs in VOR LOC mode if GS is not available - [Autoflight][PAR-8438] Fixed AP not disengaging when EFIS panel fails - [Autoflight][PAR-8441] Fixed GS law when GS is disabled from FMS - [Autothrottle] Added 1 second delay to the split monitor - [Navigation] Reset IRS drift after reposition - [Navigation] Fixed LOC CAP ACTIVE message showing when ILS is not tuned - [FMS] Improved EXEC logic - [FMS] Fixed INTC CRS not available - [FMS][PAR-9030] Fixed hold rendering not updating if modified in some conditions - [FMS] Fixed CDU crash when entering PBD waypoint at the end of the route - [FMS][DESCENT] Improved VB WPT/ALT data entry - [FMS][VNAV] Fixed acceleration after takeoff - [FMS] Fixed potential wrong order of altitude constraints for procedure - [FMS] Fixed re-selecting approach replacing current approach if already flying it - [FMS][LNAV] Fixed missing label for segments that only have one waypoint - [FMS][LNAV] Fixed incorrect distance map causing vnav errors - [Flight controls][Flaps] Improved flap load relief indicator logic - [Flight controls][Flaps] Improved flap load relief logic for SFP option - [Flight controls][Professional] Added runaway trim failure - [Flight controls] Fixed flight spoilers max deflection - [Flight controls] Fixed flap load relief - [Flight controls] Improved control column cut out switches logic - [Flight controls] Added tuning option for the control column cutout switches threshold - [Flight controls] Improved stab trim override switch logic - [Flight controls] Fixed LE flaps speed - [TCAS] General improvements Note: There are new or updated audio files due to new TCAS call outs. This will require a revision of ProSim audio configurations - [Pressurization] Added 1 second transient power protection to pressure controllers - [Pneumatic][PAR-8197] Fixed both bleed valves closing if left engine fire handle is pulled - [Fuel][PAR-9011] Improved ENG FUEL CLOSED indicator Displays - [Displays][PFD] Fixed ILS pointer handled as IAN in some conditions - [Displays][PFD][PAR-8256] Fixed take off flap maneuvering speeds for non-normal takeoff flap setting - [Displays][PFD] Added TCAS advisories (rate of climb and pitch) - [Displays][Overhead] Fixed some incorrect probe heat indicator labels - [Displays][EICAS][PAR-8814] Make engine indicator boxes brighter - [Displays][PAR-8100] Fixed altimeter amber logic using always origin data - [Displays] Added cockpit setup option to control compact engine display behavior Note: Options [Auto, Manual] Default [Auto] - [Displays][PAR-8518] Improved compact display logic - [Displays] Small adjustment to approach data - [Displays] Improved DME flag in ND and PFD - [Displays] Improved ILS deviation scales - [Displays][PFD] Fixed empty green box on FMA Drivers - [SIOC Direct] Fixed relay numbering - [SimIO] Added SimIO support to Hardware Connector - [Drivers][Phidgets22] Support for multichannel devices. - [Drivers][Phidgets22] Revised hardware listing (NOTE: Required hardware list and some mappings may require reconfiguration) - [CPFlight][ISIS] Fixed inverted GS - [Simworld] Fixed crash if MCP not present - [CDU][EHID] Fixed incorrect color formatting with large font size code - [CDU][FSC][PAR-9018] Fixed line alignment when output text is less than CDU width - [Phidgets] Added support for Digital Input Isolated Misc - [ProSimIOS] Show trim units instead of degrees - [ProSimIOS] Show flap degrees value instead of detente index - [ProSimIOS] Fixed clearing multiple failures at once did not always work - [ProSimIOS] Added support for importing Prepar3D v6 weather themes during database build - [ProSimIOS] Ensure ProSimIOS saves settings when shutdown all computers from network module - [ProSimIOS] Allow showing different recording parameters via right-click in General Statistics - [Professional][SDK] Added aircraft.flap.degrees dataref - [Professional][QTG] Added automated latency test logic - [Professional][QTG] Added CDU page to run automated QTG latency test - [Misc] Added P3D V6 support (experimental) - [Misc] Allow speed brake deploy/restow for non motorized TQs - [Misc] Fixed misspelled element name (Equip cooling exaust -> Equip cooling exhaust) - [Misc] License files are now stored in product folder (%ProgramData%\ProSim-AR\ProSimB738) - [Misc] Added compact failure list Note: To generate the new list, use http:///failuresManual?format=compact - [FS2020] STARTUP.LEGACY option is now set to FALSE by default - [Audio2] Fixed small mixer issue and added extra log May 24 2023 Release Version 3.25 ====================================== Systems: - [Datalink] Added capability to add local variables to base template - [Datalink][Templates] Added {from} field to base template - [Datalink] Added SERVICE TYPE to ATIS (VATSIM provider) - [Autoflight] Fixed missing FD bars on FO side when disconnecting AP - [Autoflight] GS approach calculations improved - [Autoflight] Fixed GS mode ready state - [Autoflight] Fixed Flight director missing in some conditions - [Autoflight] Adjusted ILS localizer tracking bias - [Navigation] Consolidated nav sources - [FMS][PAR-8607] Improved ALT CONSTRAINT nnnnn message - [FMS] Fixed CDU crash when changing PERF INIT in some conditions - [FMS] Fixed dynamic FMC messages triggered when dynamic data is empty showing placeholder in message - [FMS] Fixed LOC CAP ACTIVE triggered if APP mode not armed - [TCAS] Updated TCAS altitude threshold values - [Professional][Communications] Added 4th ASP - [GPWS] Fixed Below GS logic - [Hydraulics] Do not show refill service message if in air Drivers: - [CPFlight] Fixed crash when BRT is root module - [CPFlight] Improved MCP display to prevent/minimize value override with previous value - [CPFlight] Prevent output to display if it is closed - [SIOC Direct] Allow KEYS to be used to autodetect CDU side - [Poldragonet V2] Added MIP - [Simworld] Fixed over/under speed symbols not clearing Displays: - [Displays][VSD] Added speed prediction dot - [Displays][VSD] Improved rendering - [Display][PFD] Improved baro warning logic to allow 300ft margin Misc: - [Misc] Fixed some disagreements with virtualized ILS - [Misc][PAR-8315] Silent stick shaker if sim is not ready / paused / in slew - [ProSimIOS] Fixed possible crash when airport does not have ICAO - [ProSimIOS] Fixed online network ATC frequency with 2 digits in ProSimIOS map information - [Simconnect] Fixed initial standby QNH - [FS2020] Added tuning option STARTUP.LEGACY (Go to CDU->MAINT->PAGE 2->TUNING->MSFS2020 page) to fix engine start length for new flight model (beta) Note: Setting the option to false will adjust start tables to use newer flight model, with shorter and more accurate start sequence. Mar 8 2023 Release Version 3.24 ====================================== Systems: - [Engines][PAR-8247] Fixed combined throttle reverser not stowing - [Autoflight][PAR-8102] Fixed MCP speed changing to current airspeed if VS selected with AT off - [Landing Gear] Added inhibit logic to PSEU indicator - [FMS][POS INIT] Fixed REF GATE not accepting scenery PARKING positions - [Navigation][FMS][PAR-7996] Fixed RTE edit when moving waypoint up and has airway entry - [Navigation][LNAV] Fixed new lnav CF code should not be called if output is not a correct shortcut - [Navigation] Fixed VHF NAV source if not NORMAL - [ISFD] Fixed baro encoder still working when in STD mode - [ISFD] Fixed Capt EFIS STD setting ISFD STD if not slaved Drivers: - [Skalarki] Updated profiler library - [Skalarki] Added flap gauge support - [FDS] Fixed FDS ethernet pedestal not working - [CPFlight] Added support for CARGO V2 panel - [CPFlight] Improved flow control - [CPFlight] Added CPFlight debug window - [SIOC Direct] Fixed nav frequency leading 0 on IDC NAV radios - [CPFlight][ISFD] Fixed small altitude/barometric setting discrepancies with ProSimDisplay ISFD Displays: - [Displays][PFD] Fixed confidence test for GS scale - [Display][Pedestal] Fixed NAV 2 test - [Displays][PFD] Fixed 2 bars FD in front of center square - [Displays][PFD] Adjusted several AH elements regarding size and width Audio: - [Audio2] Fixed com test not working if not all devices are configured - [Audio2] Catch exception while adding audio devices - [Audio2] Added option to disable local intercom audio feedback - [Audio2] Fixed lost settings in main view in certain cases - [Audio2] Fixed nav audio tones not playing in some conditions Misc: - [SDK][PAR-8242] Added IRS STS dataref - [Professional Datalink] Fixed CPDLC address issue - [Professional Datalink] Added complex message support - [Misc] Added 300ft threshold for barometric warning - [Misc] Fixed beta flag in version service - [ProSimIOS] Allow using scenery BGL start positions as take-off positions Note: First new ProSimSystem database build required and new settings option in ProSimIOS "Use Scenery Take-Off Runway Positions" needs to be enabled. Then it will use the scenery BGL start position (if one is available in the scenery). - [Misc] Fixed db importer null reference for taxi path - [Misc] Reworked display code - [Control Loading] Fixed CL status not available - [FS2020] Fixed 833 spacing not properly working when simulator is set to FSUIPC - [FS2020] Fixed ZFW not accounting cargo - [CDU] Fixed FANS MCDU not activating EXEC for VNAV key - [Misc] Make reset controller dataref write only Jan 13 2023 Release Version 3.23 ====================================== Systems: - [Navigation][Professional][PROSIM737-222] Fixed LOC and GS failures names - [Navigation][IRS] Fixed NCD heading - [Navigation] Fixed ILS indications when signal is NCD - [Navigation] Fixed TCAS not flagged in case IRS has no position - [FMS] Fixed altitude legs not updating if flying below 500ft RA - [FMS] Added V speeds check logic - [FMS][PAR-7945] Fixed IRS HDG entry as true heading - [FMS][LNAV] Fixed CF legs flying too far away before turning inbound - [FMS] Reset N1 thrust limit in case of reposition for take off - [Autoflight][Commercial] Fixed missing AT failure - [Autoflight][Commercial] Fixed FD failures not working - [Flight controls][PAR-7868] Improved LE flaps indicators signal - [Flight controls] Fixed spoiler panels max deflection - [Flight controls] Improved spoiler output signal - [Flight controls] Fixed speed break factor - [Flight controls] Make sure speed break armed signal uses only lever position - [Flight controls] When in flight, speed break factor should use flight spoilers only - [Flight controls] Fixed LE devices not immediately extending when using alternate flap control - [Air conditioning] Fixed packs electric source - [Air Conditioning] Linked pack mode logic to other side switch mode instead of bleed air availability - [Ice and rain protection] Fixed cowl valve spring load not working - [Ice and rain protection] Fixed engine anti-ice power source - [Lighting] Added MIP and AFDS flood elements - [Autoflight] Make sure GA is armed when capturing the localizer - [EGPWS] Improved terrain ahead envelope check - [Hydraulics] Fixed Hydraulic pump automatic logic Drivers: - [Skalarki] Added initial hardware support - [Phidgets22] Improved device class detection - [PoldragonetV2] Fixed some issues with EFIS inputs - [FDS] Fixed MCP G1 indicators - [SIOC] Fixed SIOC MCP EFIS mappings - [SIOC Direct] Added new option to use switches for rudder trim Displays: - [Displays][PFD][PAR-7867] Fixed baro minimums pointer when RADIO minimums is selected - [Displays] Fixed light test mode for virtual pedestal panel Audio: - [ProSimAudio2] Fixed saving issue Misc: - [Control loading] Fixed E2M dll file - [Misc] Added config file manager Note: https://wiki.prosim-ar.com/index.php/Config_File_Manager - [Misc] Added DEMO MODE message to displays and CDU when running on 30 min trial - [Misc] Added End of Support message to WEB IOS - [Misc] Removed interpolators from N1 prediction arc - [Misc] Adjusted starter cutout for lower temperatures - [Misc] Fixed virtual panel sounds not playing in some conditions - [Misc] Fixed VHF COM panel test mode - [Misc] Prevent out of limits speedbrake value Nov 23 2022 Release Version 3.22 ====================================== Systems: - [Flight controls] Fixed speed brake automation - [Flight controls] Implemented auto-slat - [Flight controls] Fixed alternate flaps motor speed - [Flight controls] Added trim wheel encoder element - [Autoflight] Do not use direct simulator signal for VOR strategy - [Autoflight] Consolidated ILS LOC signal - [Engines] Improved starter valve closing timings - [Electrical] Added transient protection to GPS receiver - [Fire protection][Professional][PAR-7806] Fixed inextinguishable engine 2 fire failure Drivers: - [CPFlight] Added command to blank ISFD display Note. Requires ISFD firmware upgrade - [CPFlight][ISFD] Implemented ISFD FW version 1.7 - [CPFlight][ISFD] Improved APP mode handler - [Flight controls] Added trim wheel encoder element - [FSC][CDU] Fixed page not updating in some conditions - [FSC][CDU] Fixed degree symbol parsing - [FSC][TQ] Fixed gear warning cutout switch not working - [GoFlight] Fixed null exception when MCP detected - [Pokeys] Added support for pokeys ext bus Note: No specific configuration needed. Just assign the new output in combined config. Only output boards are supported (indicators and gates). Tested with PoRelays8 and PoExtBusOC16 Extension boards are not detected, so Prosim will send the signal to the assigned output, regardless if there is a board connected or not It is up to the user to verify if the extension board is properly connected and the order of boards if mixing boards Displays: - [Displays][PFD] Fixed scale source text overlay - [Displays] Link spoiler indication to spoiler panel Audio: - [ProSimAudio1] Fixed audio app crash when closing ProSim System and intercom is configured - Added ProSimAudio2 (BETA) Note: Refer to forum for more info [https://forum.prosim-ar.com/viewtopic.php?f=121&t=25449] Misc: - [ProSimIOS] Fixed crash when airport has no name - [Simconnect] Fixed N1 prediction stutters - [FS2020] Fixed ISFD baro setting not working in simconnect mode - [Misc] Added cockpit setup option to virtualize ILS signal Note: Virtual navaids should be enabled - [Misc] Fixed slats animations for fs2020 - [Misc] Added pax weight cockpit setup option - [Misc] Fixed some incorrect licensing text - [CDU] Added weight limit when setting load stations from cdu page - [CDU] Updated CDU maint weight page text Sep 28 2022 Release Version 3.21 ====================================== Systems: - [Indicating and recording] Improved DSPLY SOURCE dispatch indications on the PFD to DSPLY SOURCE 1 (2) - [Indicating and recording] Fixed DEU failures - [Indicating and recording][PAR-7401] Implemented DU fail auto switching - [Indicating and recording] Fixed FO side DU failures - [Indicating and recording][PAR-7384] Added gate to hold voice recorder switch in ON position - [Indicating and recording] Added power source to voice recorder AUTO/ON switch - [Indicating and recording][PAR-7409] Fixed DEU hydraulic qty source - [Indicating and recording][PAR-7409] Fixed CWS reversion for DEU failures not happening at FL220 - [Indicating and recording] DEU failure reset will now set DEU state to ready if power is available - [Autoflight][Professional] Fixed AP disengaging below 20 Kts when in operational autoland - [Autoflight] Fixed AP warning light illuminated with CWS reversion and option enabled - [Autoflight][EFIS] Fixed autopilot mode text - [Autoflight] Adjusted AFDS status box - [Autoflight] Fixed IAN approach AFDS status - [Flight controls] Fixed Speed brake armed indication - [Flight controls] Fixed LE Devices indications - [Flight controls] Fixed LE devices animations - [Flight controls] Improved slats control - [Flight controls] Adjusted flap motor speed acceleration - [Flight controls] Fixed alternate flap motor electrical load logic - [Flight controls] Adjusted LOW PRESSURE indicator threshold - [Navigation] Fixed scale source when ILS is tuned - [Navigation][VNAV] Make sure that inserting shallow segments for deceleration does not cause VNAV alt constraints to break - [Navigation][LNAV] Fixed issue where CF legs emitted different number of legs because inbound heading was A/C heading after sequencing a straight/straight path - [Navigation][LNAV] Improved altitude waypoint distance prediction - [FMS][APPROACH REF] Do not apply mag var to CRS value and always use RAW value from DB - [Landing gear] Adjusted auto brake self-test timings - [Landing gear] Added brake hydraulic actuators - [Landing gear] Fixed autobrake not disarming when system B is lost - [Anti-ice] Fixed TAT test when aspirated TAT option is disable Note: If aspirated TAT is disabled, TAT test will be INOP. - [Anti-ice][PAR-7378] Added probe heat option (AUTO/OFF) to hardware options - [Hydraulics][Professional] Added reservoir hi rate leak failures (default 10 gpm) - [Hydraulics][Professional] Adjusted pressure line leak to default 1 gpm - [Hydraulics][Professional] Added EDP line leak failures (default 1 gpm) - [Hydraulics][Professional] Added EMDP line leak failures (default 1 gpm) - [Hydraulics] Fixed STBY RUD ON indicator logic - [Hydraulics] Fixed standby pump logic - [Hydraulics] Added PTU as element - [Hydraulics] Adjusted standby pump pressure to 2700 psi - [Hydraulics] Added thermal expandability factor to reservoir qty - [Hydraulics] Indicated QTY % now shows calibrated qty instead of raw qty - [Hydraulics] Fixed Engine 1 EDP supply line - [Hydraulics] Brake accumulator will now consume hydraulic fluid - [Hydraulics] Added electrical load to standby pump - [Hydraulics] Fixed standby pump operation if bat bus not active - [Engines] Added hydraulic actuators to reversers - [Datalink] Added further data to base template header - [Datalink] Improved Simbrief config requiring ProSim restart after change - [EGPWS] Added new inhibitRange parameter to look ahead terrain modulation file (Default = 2) Displays: - [Displays] Fixed alternate flap control spring return from UP CDU: - [CDU] Fixed scratch pad not clearing in some conditions Drivers: - [Engravity] Fixed several issues with CDU V3 - [FSC] Fixed Speed brake armed indication for FSC TQs - [Phidget22] Fixed DC Motor output not detected - [Phidget22] Improved VINT detection and handling Note: Port assignment logic changed. Automatic config update will happen if upgrading to this version. But if downgrading from this version, config may be lost. It may be required to re-assign outputs/inputs - [CPFlight] Added flap speed factor value to advanced config Note: Flap speed factor can be changed in CPFlight advanced window (under Misc tab) and default value is 1.25 (25%) - [CPFlight] Slow down flap motor speed if MIPICS is detected Note: CPFlight flap gauge has a hardware fixed speed and hardware gauge does not match actual flap position. Regular flap extension time from 0 to full is about 40 seconds and CPFlight hardware moves in 50 seconds causing a mismatch between software and hardware. Flap extension/retraction times are then increased by 25% when MIP ICS is found (flap gauge present) so software and hardware gauges are in sync. - [CPFlight] Fixed tiller not working Note: Added tiller calibration capability and removed "Use tiller" option from advanced config - [Poldragonet V2] Fixed several issues - [FDS TQ] Improved trim handling Misc: - [Maintenance][BITE][FMCS] Fixed aspirated TAT discrete - [Misc] Fixed blank buttons in web IOS maint pages - [Misc][PAR-7333] Fixed fuel load issue when center tank is required to have fuel - [Misc] Also change MCP speed and altitude when repositioning - [Misc] Added source to notify hardware change events - [Misc][PROSIM737-59] Streamline UI with ProSim product line - [Misc] Fixed control panel switch logic not retaining baro settings when returning to normal - [Misc] Improved CDU failures page: Failure name is now wrapped in 2 lines for long names - [FS2020][PAR-7471] Fixed simulator QNH not adjusted in Simconnect mode - [FS2020] Fixed engine failure not working properly in Simconnect mode Aug 8 2022 Release Version 3.20 ====================================== Systems: - [Flight controls] Added new flight control surface animation - [Flight controls] Fixed spoiler movement without hydraulics - [Flight controls] Improved reverser animations - [Flight controls] Reworked flaps extension/retraction logic - [Flight controls] Added spoiler mixer as sim element Note: All the above require the new 2022 flight model - [Autoflight] Fixed AFDS status sometimes not updating - [Electrical] Fixed main buses not powered if Galley Switch option is enabled - [Navigation] Improved navigation scale source logic Displays: - [Displays] Fixed expanded scale for IAN approaches Drivers: - [CPFlight] Added CB light control mapping to overhead - [CPFlight] Force higher delay value for battery command when MIP is detected - [CPFlight] Filter incoming data to prevent noise signals to be processed - [CPFlight] Several improvements to flow control - [CPFlight] Added extra delay when sending battery command Misc: - [Misc] Added CB light control elements - [Misc] Added null zone to analog trim elements - [Misc] Added local UI test for gates - [ProSimIOS] Adjusted wind readout in current weather - [ProSimIOS] Fixed TCAS intruders not correctly removed - [CDU] Fixed issue causing some CDU based drivers to crash - [FS2020] Fixed database build with SU10 Jul 7 2022 Release Version 3.19 ====================================== Systems: - [Hydraulics] Fixed accumulator pressure dropping below 1000 when on bat only - [Hydraulics] Improved brake pressure gauge output - [Datalink] Added base template note: This base template can be used to customize header/footer and add extra lines at the end to allow cutting space depending on the printer used. - [Datalink] Fixed RCVD MSG page not refreshing after RETURN from message - [Datalink] Fixed CDU crash when loading PERF uplink in some conditions - [Datalink] Fixed fuel loading issue in Simconnect mode - [FMS] Fixed early descent lock - [FMS] Fixed underspeed symbol in some specific conditions - [FMS][VNAV] Fixed AT going to ARM at T/D and in level flight - [FMS][LNAV] Fixed waypoint overlapping in some conditions - [Indicating] Do not trigger CDS FAULT after second engine start - [Indicating] Fixed CDS FAULT not triggering DSPLY SOURCE after second engine start - [Fire Protection] Fixed fire indicators triggering master caution OVHT/DET - [SMYD][Professional] Consolidate VSS between speed tape and MCP logic Displays: - [Displays] Fixed amber WHEEL WELL indicator Drivers: - [Poldragonet] Added support for new 737 hardware panels - [CPFlight] Fixed new WXR panel not working - [CPFlight] Fixed indicator issue with first generation ICS MIP - [Phidgets22] Fixed Advanced LED outputs when using indicator intensity higher than default values Misc - [ProSimIOS] Fixed turbulence options sometimes changed by itself if Active Sky was not used - [ProSimIOS] Don't force reset weather when switching from weather preset to custom weather - [Misc] Added overhead backlight control elements - [Misc] Fixed WXR2100 radar panel TFR switches not latching - [FS2020][Misc] Fixed ILS heading issue for scenery items that use non fixed heading - [FS2020][Misc] Fixed potential scenery object airport skipped when delete information is not set Jun 03 2022 Release Version 3.18 ====================================== Systems: - [Navigation] Added AoA Disagree flag - [Navigation] Fixed ILS transmitter failures causing ILS flags - [Navigation] Added individual ILS channels (LOC/GS) failures - [FMS] Added max CRZ N1 tables - [FMS] Improved MAX CON N1 value - [FMS][PROGRESS] Make sure correct route source data is in use for predictions - [FMS][FIX] Register all runways from origin/destination - [LNAV] Fixed CI to FD sequencing - [LNAV] Offset improvements - [LNAV] Fixed intercept into CF with turn - [LNAV] Do not allow bypass for waypoints with overfly - [Flight Controls] Fixed auto trim with AP off - [Flight Controls] Fixed overrun trim in some conditions - [Engines] Fixed negative N1 with engine off and WAI ON - [Engines] Improved reverser indication logic Displays: - [Approach Ref] Added frequency flag - [Approach Ref] Improved CRS flag Drivers: - [CPFlight] Added standby module - [CPFlight] Improved communication flow control - [CPFlight] Fixed Ethernet CDU color option not persistent Misc: - [FSUIPC] Improved FS Command offset logic - [ProSimIOS] Added support for new IVAO data format - [Audio] Updated audio files - [Misc] Fixed occasional ProSim not responsive at startup, in FSUIPC mode, if simulator is not running - [QTG] Ignore calibration and augmentation if SDK driver is in use - [SDK] Added SDK printer datarefs Note: aircraft.datalink.printer.enabled - Enables the SDK print queue. Enabling the queue will disable any other printer selected in datalink config, regardless if it is enabled or not. It will also make the PRINT prompt available for a printable message aircraft.datalink.printer.control - SDK printer control. Commands: Query: returns number of print jobs on hold in queue Print: returns the content of the first print job available May 2 2022 Release Version 3.17 ====================================== Systems: - [Autoflight][BETA] Added elevator based AP pitch channel Note: Use AS IS Pitch command will use elevator first, then trim will be used to move elevator to neutral position - [Flight Controls][Elevator Trim] Reworked trim logic with correct trim speeds for both elec manual or elec AP Note: New gates added for different trim speeds (AP/MANUAL) and new numerical output with factored trim speed value Old gates and numerical outputs will co-exist for backward compatibility For TQs with own logic, like script based, scripts need to be adjusted to make use of this new functionality. ProSim is not responsible for this task ProSim based TQ drivers will be updated at a later stage - [Flight Controls][Elevator Trim][BETA] Implemented closed loop trim Note: Use AS IS Trim command will be sent to trim motor and trim wheel rotation will actually send trim command Not all TQs support this, so use this carefully Option to enable and factor value added to ProSim config->Throttle/MCP Factor value is hardware dependent and in no way ProSim can provide this number 2 main factors will affect factor value. Actual trim motor speed and how TQ sends manual trim input If hardware TQ does not support manual trim input, it does not support closed loop - [Datalink] Fixed ACARS pages not working when incorrect company ICAO code entered - [Datalink][CPDLC] Handle FLIGHT PLAN NOT HELD message and reset logon request - [Datalink][CPDLC] Improved logon handler if station is not online - [ACARS] Added further log to legacy mode - [Autoflight] Fixed altitude acquisition alert when changing MCP altitude - [Autoflight] Reduced wind compensation factors for autothrottle law - [VNAV] Tuned turns while on PATH - [VNAV] Fixed descent angle below the descend-speed-restriction - [LNAV] Reset CF leg inbound course if waypoint before is replaced to prevent render issues - [FMS] Fixed CF course not reset after DCT TO a CF leg - [FMS][REF NAVDATA] Fixed missing EXEC - [FMS][DES FORECAST] Improved wind data entry - [FMS][RTE] Fixed null pointer exception when deleting flight number - [FMS][FIX] Verify route waypoints first - [FMS][POS SHIFT] Fixed page not working - [FMS][LEGS] Fixed some custom waypoints not accepted - [FMS] Fixed flight number dashed in xml output - [Landing Gear] Fixed gear warning with flaps 25 during take off - [Electrical] Added Galley / Cab Util switch hardware option Note: Please select proper option for the hardware overhead in use - [Communications] Sync ASP send switch - [Communications] Set xmit radio on start up - [Engines] Added EEC ON indicator hardware option Note: Please select proper option for the hardware overhead in use. normally it should be simulated unless you have an OEM panel Displays: - [VSD] Fixed cyan MINS triangle in some conditions - [VSD] Fixed reference altitude - [VSD] Added VSD flags - [PFD] Confidence test duration extended to 4 seconds - [ND] Fixed some elements visibility in PLN mode - [ND] Fixed ADF needle not showing - [Engravity] Added support for CDU V3 - [Phidgets22] Fixed indicator finder not working Drivers: - [CPFlight] Prevent input processing when closing ProSim - [CPFlight] Added color option to CDU PRO configuration - [CPFlight] Fixed swapped PACK L & BLEED TRIP L indicators for the ethernet overhead - [CPFlight] Added MIP backlight control mappings - [CPFlight] Added ISFD backlight control - [SIOC Direct] Show BANK LIMIT on heading display when heading selector is pressed for MCP V2/V3 - [GoFlight] Fixed system driver not working Misc: - [SimConnect] Fixed fuel loading issue - [Doors] Added option to control air stairs in a similar way as doors (ProSim / external) - [Overhead] Fixed galley switch not working if option enabled Note: If hardware Cab/Util option is enabled, galley switch will not work from the software panel. - [CDU] Fixed CDU page not refreshing in some conditions - [SDK] Added VOR datarefs for bearing - [SDK] Added ADF datarefs for bearing - [SDK] Added IRS datarefs for heading - [ProSimIOS] Fixed failure conditions of arm failures not always correctly shown - [ProSimIOS] Added settings option to enable confirmation dialog before ProSimIOS close - [Misc] Fixed motor trim direction gates - [Misc] Fixed MINS reset not in synch when FO slave option enabled - [Misc] New cockpit setup option to change pitch channel from trim to elevator based - [Misc] Fixed wxr radar mode not working for RDR4B panel models - [Misc] Fixed wxr radar right mode not working for RDR4000 panel models - [EFIS] Fixed selector not in sync with displays on start up - [Misc] Added MIP dimmer elements - [Misc] Updated average pax weight to 88 Kg - [Misc] Added gate to allow parking brake switch action - [Misc] Added new cockpit setup option to link FO EFIS baro/radio option to capt EFIS Note: Removed link FO QNH to Cap QNH option - [Misc] Added hardware options capability - [Misc] Fixed small issue when setting ADF frequency from the CDU Apr 1 2022 Release Version 3.16 ====================================== Systems: - [FMS][PROGRESS] Fixed rwy waypoint showing destination ICAO code - [FMS][PROGRESS 2][PAR-6526] Fixed wind available when on ground - [FMS][PROGRESS 2] Fixed small layout issues - [FMS][PERFINIT][Commercial] Fixed PLAN header not shown - [FMS][PERF INIT] Fixed ERASE not available - [FMS][PERF INIT] Fixed modified mode when first entering data - [FMS][CRZ] Fixed wind available when on ground - [FMS][RTE] Fixed page not refreshing after invalid uplink - [FMS][RTE] Fixed TA not loaded with uplink - [FMS][RTE] Fixed IF legs not retaining constraints for STAR/APP phases - [FMS][LNAV] Revised single bypass code - [FMS][FIX] Also use modified route to search for rwy waypoints - [FMS][N1 LIMIT] Fixed OAT not mandatory - [FMS][N1 LIMIT] Fixed N1 selected when OAT not available - [FMS][TAKE OFF] Fixed QRH speeds not shown with modified PERF INIT - [FMS][TAKE OFF 2] Fixed N1 header - [FMS][ALT DEST] Fixed MISSED APP values - [FMS] Fixed internal crash when performing a GA in some conditions - [FMS] Reworked EXEC logic (not all pages will show EXEC illuminated) - [FMS] Revised Time estimations (RTE and LEGS page are now using same calculations) - [FMS] Fixed altitude restriction not accepted if route not active - [FMS] Fixed alt/speed restriction climb flag logic (causing some VNAV issues) - [FMS] Fixed constraints not updating route markers when in modified mode (i.e T/D not changing) - [FMS] Added ALT CONSTRAINT yyyyy FMC message - [FMS] Added CRZ ALT CHANGED TO zzzzz message - [FMS] Fixed PERF INIT reset when erasing CLIMB page - [FMS] Fixed trip alt not recalculated if ZFW entered in last - [FMS] Revised trim tables - [FMS][Commercial] Fixed snapshot not working - [FMS] Make ALT CONSTRAINT message available for beta versions only - [FMS] Do not use missed approach segment for min crz altitude check - [FMS] Fixed ALT INTV handler in case altitude constraint waypoint also has speed constraint - [FMS] Fixed DISCO leg not properly defined in some conditions - [FMS] Prevent route continuity when deleting/replacing DISCO after VECTOR leg - [FMS] Fixed user entered leg course not updated in some conditions - [LNAV] Fixed CF leg not acknowledging flyover - [LNAV] Fixed CF teardrop error in drawing - [LNAV] Improved route drawing - [LNAV] Improved single bypass logic - [VNAV] Fixed VNAV DISCONNECT during climb - [LNAV] Fixed small issue in "CF" track code - [LNAV] Fixed issue where waypoint with holding is sequenced too early - [VNAV] Fixed default decel segment issue in some extreme conditions - [VNAV] Fixed commanded MACH above MMO in some conditions - [Autoflight] Improved closed loop Note: New tuning factor available (ProSim config -> MCP/Throttle). Default value is optimal value for FDS MX TQ - [Autoflight] Added min/man closed loop factors - [Autoflight] Added tunning parameter to test alternate AT speed mode (reduced wind compensation factors) - [Autoflight] Fixed overspeed/underspeed symbols not working on MCP - [Electrical] Connect metering display to hot battery bus - [EFIS][PROSIM737-208] Fixed amber barometric at high altitude airports - [GPWS] Added cockpit setup item to ignore gear position for altitude call outs - [EGPWS] Improved terrain drawing logic - [EGPWS] Improved peaks logic - [Engines] Motoring tuned - [Engines] Fixed START GND not working in flight - [Engines] Fixed motoring - [Engines] Revised start sequence - [Engines] Fixed inflight engine start - [Engines] Fixed no indications and N2 values during start switch changes - [Engines] Fixed start switch not aborting start sequence - [Engines] Fixed starter state in simulator - [Engines] Fixed ENG FAIL flag on engine starting after shutdown Displays: - [ND] Fixed debug marker showing in some conditions - [ND] Fixed PLN mode clipping - [ND][PROSIM737-156] Small improvement to GS on ND - [ND] Consolidate inactive route color Drivers: - [VRInsight] Added wiper mappings - [Phidget22] Fixed missing calibration controls for DC motor cards - [Phidget22] Fixed crash when using 1.10xx library - [FDS] Added generic boards for ethernet driver - [Phidget] Analog Inputs sensitivity changed to double - [SIOC] Fixed missing MCP indicator logic required for script-based hardware Misc: - [Misc] Fixed sim rate not working from CDU page - [Misc] Prevent flame out if center tank is loaded with 0 fuel and center tanks are ON - [Misc] Fixed mirrored CRS1/CRS2 when FSUIPC support for MCP is enabled - [Misc] Added cockpit setup option to completely disable GPU control when using the GND CALL - [Misc] Added N1 ref datarefs - [Misc] Added switch element to reset attend call - [Misc] Added datarefes to control external panels - [Misc] Improved direct input axis resolution - [Misc] Added filter to N1 prediction arc - [Misc] Fixed wxr radar decimal values - [Misc] Fixed ProSim crash when IOCP driver is in use and encoders are assigned - [Misc] Fixed SQUAWKBOX offsets not working - [Misc] Added further initialization log - [Misc] Fixed RDR4B weather panel default mode - [Misc][Professional] Added cockpit setup option to select actual simulator wind or IRS sensed wind for FMS use - [Misc][Professional] Fixed vibration gate with bird strike - [FS2020] Adjusted engine start script to match FS2020 ProSimIOS: - [ProSimIOS] Fixed certain IOS commands (like APU quick start) not working - [ProSimIOS] Extended custom weather surface layer to better reflect surface weather settings - [ProSimIOS] Custom weather improvements - [ProSimIOS] Added weather preset context menu option to manually edit METAR string - [ProSimIOS] Fixed Aircraft status of towing PIN not updated - [ProSimIOS] Added external panels call switches - [ProSimIOS] Fixed temperature layers when Active Sky was not used - [ProSimIOS] Fixed surface temperature for high altitude airports - [ProSimIOS] Fixed clouds display text in METARs - [ProSimIOS] Fixed custom weather turbulence selection sometimes changed by itself Feb 15 2022 Release Version 3.15 ====================================== System: - [Autoflight] Improved GA arming logic - [Autoflight] Fixed LNAV indicator not illuminating in some conditions - [BITE][APU] Fixed ProSim crash when viewing INPUT MONITORING page 4 - [FMS] Fixed ProSim crash when trying to load empty origin/destination - [FMS][GA] Refresh LNAV in case of go around - [FMS][RTE] Fixed ORIGIN auto-populated with DESTINATION when ORIGIN is empty - [Pressurization] Added digital outputs for duct pressure digital gauges - [Engines] Fixed excess vibrations in normal conditions - [Engines] Fixed ENG FAIL flag logic - [Fire] Added fire bell gate - [Datalink] Improved AOC uplinks page - [Datalink] Fixed route uplink with PERF INIT uplink - [Datalink] Clear uplinks on FMS reset - [Datalink] Added NOTAMS request Note: Simbrief required - [Datalink] CPDLC added Note: Hoppie required - [Datalink] Added Hoppie as WT BALANCE / LOADSHEET provider Note: Capability using hoppie file storage. Following TOPCAT naming rules. TOPCAT CC should match airline icao code in ProSim config. - [Datalink][Printer] Added printer for legacy mode - [Datalink] Added airline info to config - [Datalink][Printer] Added default printer font - [Datalink][Printer] Fixed font style - [Datalink] Fixed cpdlc uplink not marked as uplink - [Datalink] Fixed INIT DATA fields not editable - [Datalink][CPDLC] Defaults are now also read from ACARS DATA INIT if present - [Datalink][Professional] Fixed occasional exceptions when selecting CPDLC message on IOS - [Datalink][Professional] Fixed WT/BALANCE not working with SDK Displays: - [Display] Added digital round clock Drivers: - [GoFlight] Fixed MCP crash - [Phidget22] Fix some occasional crashes - [Phidget22][FDS TQ] Improve IO element out timings - [Phidget22][FDS TQ] Power management fixed - [Phodget22][FDS TQ] Updated phidget library to 1.9.20220112 Note: It may require user to update phidget control panel to same version - [FDS TQ] Fixed shutdown crash - [FDS TQ] Improved performance - [FDS TQ] Fixed crash when handling other phidgets Misc: - [SimConnect] Increased TCAS range to 40NM - [ProSimIOS] Added note for failure reset conditions that cannot be triggered manually - [ProSimIOS][Commercial] Fixed slew not working properly with FSUIPC - [FSUIPC] Fixed AI traffic not shown on ProSimIOS map - [Misc] Normalizing SimConnect/FSUIPC engine vibrations value - [Misc] Autoflight code rework in preparation for future improvements - [Misc] Added engine text to bird strike failures - [Misc][Professional] Added failure class to auto reset failures - [Misc] Fixed speed brake free servo config not persistent - [Misc] Revised code to prevent old script based TQ/MCP from work Note: This requires the simulator to be in FSUIPC mode and "Control via FSUIPC" option enabled (ProSim Config -> MCP/Throttle -> General Drivers -> For other MCPs) Jan 18 2022 Release Version 3.14 ====================================== System: - [Engines] Fixed vibration failures - [Engines] Fixed throttle not going to idle in some conditions - [FMS][DES FORECAST] Fixed missing CABIN RATE value - [FMS][PERF INIT] Fixed missing page header state (MOD/ACT) - [FMS][PERF INIT] Fixed uplink not allowing execute - [FMS][DEP/ARR] Small adjustment to page title - [FMS][DEP/ARR] Fixed 4th missing approach transition when GS line is visible - [FMS][VNAV] Fixed issue where departure speed restrictions are not handled properly - [Landing Gear] Fixed NWS transfer valve output - [Pneumatic][Pressurization] - Fixed outflow valve moving when controller not powered Datalink: *** NOTE: FOR ALL DATALINK FUNCTIONALITY *** CONSIDER FLIGHT NUMBER AND AIRLINE INFO MANDATORY - [Datalink] Implemented new datalink model supporting SimBrief (Beta) Note: Currently limited to just a couple of messages and for evaluation purposes *** New system is not compatible with any ACARS addon, like ProSimUtils *** New options added to config - Legacy ACARS: Select between old XML based ACARS and new system (Enabled by default) - Simbrief: Siembrief ID. Will allow direct downlink from CDU pages (new REQUEST prompt should be visible where applicable) - [Datalink] Added templating capability Note: A Datalink/Templates folder should be available inside ProSim-System main folder. Default templates can be found in there. In case of custom templates, template should be copied from system folder to ProgramData\ProSim-AR\ProSimB738\Datalink\Templates end edited. Custom template will have priority over default one - [Datalink] Added Airline info to config Note: For now, Airline data can only be changed via manual edition of the config.xml file - [Datalink] Added ATS ATIS requests Note: ATIS is only available when using hoppie provider (using hoppie vatAtis request) - [Datalink] Added AOC RAMP SERVICE REPORT Note: This report was added to validate and test the templating functionality AirlineIcao code (from config) will be used as dispatch address - [Datalink] Added generic uplink advisory - [Datalink] Added hoppie TELEX support - [Datalink] Revised config window - [Datalink] Added print capability - [Datalink] Fixed datalink service available if not configured - [Datalink] Fixed weather providers - [Datalink] Fixed PERF INIT request - [Datalink] Fixed simbrief config Note: If username is entered, even if not valid, prosim will always use it. To use the user id, username field must be blank - [Datalink] Fixed route uplink not allowing RTE LOAD - [Datalink] Fixed initialization - [Datalink] Added datalink failures (FAIL, NO COMM) - [Datalink] Added VATSIM as ATIS provider Note: ProSim will only search for _ATIS stations. - [Datalink] Added data entry verification to ATIS REQ page - [Legacy ACARS] Fixed variables not filling with default data - [Datalink][AOC] Added INIT DATA page - [Datalink] Fixed time format in RETURN prompt - [Datalink][AOC] Fixed WX REQUEST page - [Datalink][AOC] Added FLT PLAN request prompt to REQUESTS and PREFLIGHT pages - [Datalink][AOC] Added PREFLIGHT page - [Datalink] Fixed review message page - [Datalink][AOC] Added WT/BALANCE request - [Datalink] Removed blank page interval - [Datalink][PERF INIT] Fixed ZFW value not loaded - [Datalink] Added inactive advisories - [Subsystem] Fixed subsystem logoff - [Datalink] Added time to RETURN prompt - [Datalink] Added ATS - DEPARTURE CLX Note: Currently only hoppie is available as provider. Answer should be received as Telex message - [Datalink] Added EICAS advisories Note: Required cockpit setup option enabled - [Datalink] Added chime Note: Chime behavior can be controlled from cockpit setup option - [Datalink] Improved free text area - [Datalink] Fixed ACARS not working when CPDLC is not available - [Datalink] Telex provider will now use tail number in case flight number is not filled - [Datalink] Added cockpit setup option to load cargo/pax (Default: Enabled) - [Datalink] Added cockpit setup option to load fuel (Default: Enabled) - [Datalink] Received messages are now sorted descending - [Datalink] Added active advisories - [Datalink][VATSIM] Prevent empty uplink when ATIS is not available - [Datalink][Config] Fixed duplicated printer entries - [Datalink] Fixed empty print output for template based uplinks - [Datalink] Differentiate VATSIM ATIS message when station not online or provider failed with log entry in case of service fail - [Datalink] Prevent CDU crash in case of empty weather message - [Datalink] Differentiate WEATHER message when selecting invalid station - [Datalink] Fixed occasional CDU crash after FMS RESET - [Datalink] Clear FMS uplinks after FMS RESET - [Datalink] Fixed wind uplink not loading in some conditions - [Datalink] Added CRZ WIND to PERF INIT uplink - [Datalink] Fixed SSL connection to VATSIM - [Datalink] Fixed ignored printer columns value - [Datalink] Fixed received messages page Displays: - [VSD] Fixed terrain not available Drivers: - [FDS] Added native support for FDS MX TQ Note: Requires specific phidget control panel Version 1.7.20211005 Using different versions may result in unexpected behavior - [FDS TQ] Fixed autodetection when ProSim is already running - [FDS TQ] Fixed trim - [CPFlight] Added missing NWS switch mapping - [CPFlight] Added support for new MIP ICS 3 Misc: - [Maintenance] Fixed BITE not working when legacy ACARS is selected - [Misc] Fixed flap reset after reposition - [Misc] Fixed closed loop throttle option Dec 13 2021 Release Version 3.13 ====================================== System: - [Navigation] Fixed Below GS signal - [FMS] Fixed wind data source - [FMS] Fixed CDU crash when adding PBD waypoint at the end of flight plan - [FMS] Fixed manual N1 reset - [Landing gear] Fixed brake temperature indication - [Electrical] Fixed wrong Ampere values - [PROSIM737-182][Autoflight] Fixed AP engaging with trim cutout - [PROSIM737-182][Autoflight] Added control column cutout functionality - [Engines][Startup] Logic reviewed and improved - [Engines] Fixed Shutdown engine problem - [Engines][Commercial] Added severe damage failure - [Engines][Startup] Fixed N1 ending difference from start sequence and P3D model - [Engines] Fixed reversers when switch is used as input Drivers: - [CPFlight] Fixed BLEED LEFT / BLEED TRIP LEFT swapped indicators Misc - [QTG] Fixed QTG transport delay screens - [FS2020][Autoflight] Tuned MCP speed / level change mode - [FS2020][Simconnect][Communications] Fixed COM1 handling - [ProSimIOS] Fixed airworks altitude - [WebIOS][Commercial] Fixed some elements missing from SERVICE tab - [Misc] Added further log to webserver - [Misc] Fixed several sim elements linked to incorrect license Nov 12 2021 Release Version 3.12 ====================================== System: - [FMS] Removed beta flag from energy compensation cockpit setup option - [FMS][HOLD] Fixed occasional exception when hold waypoint is last in route - [Electric] Fixed generators with wrong or zero ampere and voltage values - [EFIS] EFIS RST will now show/hide MINS indication instead of hide only - [Fire][Commercial] Fixed engine extinguishable fire with 2 bottles Displays: - Fixed storing display layout on certain systems Drivers: - [EHID] Added missing Capt PTT mapping Misc: - [ProSimIOS] Fixed shutdown all networked computers did not always work - [ProSimIOS] Fixed detached Map module got disabled when selecting Height Map - [SDK] Fixed aircraft.flightControls.trim.aileron.normalized and aircraft.flightControls.trim.rudder.normalized datarefs not available despite correct licence - [Commercial] Fixed FMS state serialization Oct 15 2021 Release Version 3.11 ====================================== System: Autoflight - [Maintenance][AT BITE] Fixed servo test not working Navigation - [FMS] Fixed extra destination airport legs after go-around - [FMS] Fixed FMC position available if FMC is failed - [FMS][Commercial] Fixed flight deck effects for FMC failure - [FMS][VNAV] Fixed decel segments logic using cruise instead of descend speed - [FMS][PERF INIT] Fixed wind entry crashing CDU when route not active yet - [FMS][HOLD] Fixed hold ETA - [FMS][HOLD] Improved hold best speed and leg time logic - [FMS][HOLD] Fixed exit hold drawing full hold pattern when leg time modified - [FMS][LEGS] Fixed RTE ETA not using EFC (HOLD TIME) - [FMS][LEGS] Fixed HOLD speed - [FMS][LEGS] Fixed multiple magenta lines in some instances - [FMS][RTE] Fixed DIRECT replacement with airway not adding intermediate waypoints - [FMS][RTE] Fixed airway entry - [FMS][RTE] Fixed SELECT DESIRED WPT if waypoint not in airway - [FMS][RTE] Fixed HOLD label after DIRECT TO - [FMS][FIX] Fixed departure RWY waypoint not accepted - [Maintenance][ADIRS BITE] Fixed ADR TAT and TAS test values - [Maintenance][ADIRS BITE] Fixed IR wind, mach and GS test values on ND Flight Controls - [Flaps] Fixed flaps returning to handle position when using alternate flaps - [Flaps] Fixed load relief activation when using alternate flaps - [FlightControls] Fixed erratic rudder trim Other - [Electrical] Fixed elec display values showing decimal places - [Maintenance][FQIS BITE] Fixed page navigation Displays: - [ND] Fixed ND flags not showing in zoom mode - [ProSimDisplay] Fixed terrain crashing display app Misc: - [ProSimIOS] Fixed magnetic variation not always correctly considered during heading display on IOS. - [ProSimIOS] Fixed did not close automatically when Windows shuts down if no connection to ProSimSystem - [ProSimIOS] Improved cloud definition now always AGL (requires rebuild of ProSimSystem database) - [ProSimIOS] Fixed Active Sky real-time weather deactivated after reposition - [Commercial][Windshear] Fixed windshear not working with simconnect - [Misc] Recheck AP after reposition Note: If reposition to ground, AP and AT will disengage. In case VNVA/LNAV are engaged, reversion to HDG SEL/ALT HOLD will happen. If AP is already in HDG SEL / ALT HOLD then MCP will be re set to position data. Any other combination will disengage the AP - [Misc] Fixed pressurization reset after reposition to high altitude - [Misc] Fixed an issue causing airstairs in the 2021 flight model to not work - [Misc] AoA and Radio Altimeter cockpit setup options are now exclusive - [Misc] Added cockpit setup option to inhibit TFC,RFCF and TerrainAhead EGPWS modes - [Misc] Extended EGPWS modulation file to define modulation exclusive or inclusive Note: It is now possible to disable a mode by default, where modulation can be used to enable for specified airports. - [Misc] Fixed underlying sim lights not working with SimConnect(P3D) - [Misc] Added further vnav debug info - [Misc] Added further lnav debug info - [Misc] Added web call to get GPWC modulation file http://127.0.0.1:8080/gpwcSample Sep 17 2021 Release Version 3.10 ====================================== System: Navigation - [CDU] Improved INIT/REF key behavior - [FMS] Fixed null exception when speed error exists without speed restriction - [FMS][Commercial] Added cockpit setup option to disable UNABLE NEXT ALT alert message (Debug option) - [FMS] Prevent intercept line to be drawn in some conditions - [FMS] G/A rework - [FMS] Improved LOC CAP ACTIVE advisory message - [FMS] Revised trim tables - [FMS] Revised V speed tables - [FMS] Fixed vSpeed calculation always using 26K table - [FMS] Fixed TOGA not engaging in raw mode (no fms data) - [FMS] Fixed empty fuel predictions when arrival not entered yet - [FMS][RTE] Improved RTE page sequencing - [FMS][RTE] Intercept line should only be visible with LNAV active - [FMS][RTE] Fixed FROM leg showing in some conditions - [FMS][LEGS] Fixed PBD waypoints not accepted in some conditions - [FMS][LEGS] Fixed rwy waypoint rename when selected for a DIRECT TO - [FMS][LEGS] Fixed issue causing multiple lines to be magenta - [FMS][LEGS] Fixed DISCO not added before STAR in some conditions - [FMS][CLB] Fixed cruise level handler - [FMS][TAKEOFF] Improved N1 value refresh - [FMS][N1 LIMIT] Selecting D-TOn, should automatically select equivalent D-CLBn - [FMS][N1 LIMIT] Fixed assumed temp not resetting after rwy/departure change - [FMS][N1 LIMIT] Fixed derates not resetting after departure or runway change - [FMS][DEP ARR] Fixed CDU crash in some instances - [FMS][DEP ARR] Fixed missing approach transition when IAN is enabled - [FMS][PROGRESS 4] Fixed missing vertical deviation - [FMS][HOLD] Fixed MOD not updating PPOS hold - [FMS][HOLD] Added DISCO after PPOS hold - [FMS][CLB] Fixed missing climb restriction at LSK1R Landing Gear - [Landing Gear] Fixed rudder not controlling nose wheel steering Note: Rudder pedals will now control nose wheel steering when independent mode is active - [Landing Gear] Added nose wheel steering failure - [Landing Gear] Added towing pin control (IOS and CDU MAINT) Engines - [Engines] Fixed ground FF - [Engines] Vibration failures reworked Other - [Autoflight] Allow MCP speed to be in upper amber band - [APU][Commercial] Added APU generator failure - [Wxr Radar] Fixed AUTO mode not working properly Note: P3D/AS does not provide true auto mode functionality. So just auto tilt is provided based on aircraft pitch - [Engine Faults][Commercial] Fixed incorrect flight deck effects for several start faults - [Lighting] Added pedestal panel light control elements - [EGPWS] Added (E) modes: Terrain Ahead, TCF and RFCF Displays: - [PFD] Make sure VSS flag is NO when in air - [ProSimDisplay] Fixed Oxygen pressure gauge - [ProSimDisplay] Fixed mouse dragging issues - [ProSimDisplay] Fix Windows 8 and AMD issue - [ND] Fixed wxr fail flags - [ND] Fixed extra wxr annunciation on FO ND - [SEI] Fixed pointers going out of scale - [SEI] Fixed pop up not working when vibration goes amber - [EICAS] Fixed vibration not changing to amber when above limit - [General] Fixed image encoder rotation issues Drivers: - [CPFlight][Overhead] Fixed solenoids resetting after light test - [CPFlight][Overhead] Fixed indicator mappings - [FDS Ethernet] Removed empty spaces from host name to allow proper module detection - [CPFlight] Added option to swap gain/tilt controls for new wxr radar panel - [CPFlight] Updated AUTO and L/R mapping to latched type - [CPFlight][CDU PRO] Added backlight control from pedestal Misc: - [ProSimIOS][Professional] Added towing PIN control - [ProSimIOS] Fixed existent triggered failures not shown on IOS when ProSimSystem was started first - [ProSimIOS][Commercial] Added support for windshear without Active Sky - [Control Loading] Fixed several issues - [Misc] Fixed NWS for combined mode - [Misc] Added cockpit setup option to show/hide N1 Gauge caret value (green max N1) - [Misc] Added cockpit setup option to show N1 Gauge caret value with assumed temp calculation - [Misc] Improved CPU usage - [Misc] Fixed analog trim elements range - [Misc] Fixed SDK not working - [Misc] Added analog trim elements - [Misc] Also sync STD when Captain QNH controls F/O QNH option is enabled - [Misc] Virtual navaids enabled by default - [Misc] Added wiki user manual link to the Help menu Aug 11 2021 Release Version 3.09 ====================================== System: Navigation - [FMS] Revised VREF tables - [FMS] V speeds are now adjusted for slope/wind/altitude - [FMS] Added VREF SFP table - [FMS] Added V1MCG table - [FMS] Added NAV INVALID-TUNE xxxxx alerting message - [FMS] Added RW/APP TUNE DISAGREE alerting message - [FMS] Added FMC APP MODE UNAVAIL-GP advisory message - [FMS] Added V SPEEDS UNAVAILABLE advisory message - [FMS] Added MCP APP DISARM REQD advisory message - [FMS] Added RESET MCP APP MODE advisory message - [FMS] Added LOC CAP ACTIVE advisory message - [FMS] Added LOC CAP CANCELLED advisory message - [FMS] Prevent "RESET MCP ALT" message if there is a hold between A/C position and T/D - [FMS] Fixed take off AT mode on VNAV - [FMS] Fixed STEEP DES message showing for discontinuity - [FMS] Fixed issue where modified route was returning wrong cruise speed - [FMS] Improved hold DECEL marker - [FMS] Fixed level segment when altitude restriction of same value of cruise level is added to enroute segment - [FMS][VNAV] Fixed MCP altitude overshoot when on early descent - [FMS][VNAV] Improved DES NOW logic - [FMS][VNAV] Added OVERSPEED DISCONNECT alerting message - [FMS][VNAV] Added VNAV DISCONNECT alerting message - [FMS][VNAV] Added VNAV INVALID-PERF alerting message - [FMS][VNAV][Professional] Added VNAV EXCEPTION failure - [FMS][IDENT][Commercial] Allow simulation of ACTIVE / STANDBY database change - [FMS][IDENT][Commercial] Improved NAVDATA OUT OF DATE message when changing cycles - [FMS][RTE] Fixed discontinuity after last waypoint from company route - [FMS][U13][RTE2] Fixed RTE2 ERASE removing also origin and destination - [FMS][LEGS] Fixed STEP not in sync when changing EFIS from PLAN to MAP and back - [FMS][LEGS] Fixed wind and vnav data entry modifying route when data is invalid - [FMS][LEGS] Fixed altitude restriction for enroute accepting values greater than cruise level - [FMS][LEGS] RW speed should be empty if no vref speed entered - [FMS][LEGS] Fixed FA legs not showing TRK on direction label - [FMS][TAKEOFF2] Fixed missing climb thrust - [FMS][CRZ] Fixed CRZ DES mode - [FMS][CRZ] Improved CRZ CLB/DES mode handler - [FMS][DES] Fixed cdu crash when hold is active and calculated speed is in mach - [FMS][DES] Fixed null reference - [FMS][APPROACH REF] Allow deletion of vref speed/flaps - [FMS][HOLD] Fixed HOLD AVAIL not available if route has modification - [FMS][HOLD] Fixed EFC returning INVALID ENTRY when ETA is close to 24:00 and EFC is already in the next day - [FMS][HOLD] Fixed Speed/Alt not showing calculated values - [FMS][HOLD] Fixed null reference - [FMS][HOLD] Fixed HOLD AVAIL using EFC for calculation - [FMS][HOLD] Improved page layout when exit armed - [FMS][HOLD] Fixed ERASE prompt not avail when exiting the hold - [FMS][HOLD] Added UNABLE HOLD AIRSPACE alerting message Note: When outside the hold, if an attempt to exit the hold is done, this message will appear. Perform a DIRECT TO to exit the hold. - [FMS][N1][PAR-5620] Improved CLB derate recalculation Autoflight - [Auto-throttle] Improved TO/GA response - [Autoflight] Fixed hold speed not commanded when already commanding mach Other - [Pneumatic][Commercial] Added bleed trip (no reset) failure - [APU] Fixed APU not starting after an APU fault reset - [APU] Fixed APU FAULT light not illuminating with APU failure - [APU] Fixed protective shutdown not illuminating APU FAULT - [WAI] WAI should affect N1 value Misc: - [FM] Fixed flight model handler - [Engine start faults][Commercial] Flight deck effects reviewed - [SimConnect] Fixed some data inconsistencies - [Misc] Improved wxr radar split controls handler - [Misc] Fixed engine start - [Misc][Commercial] Improved engine start failures (correct flight deck effects) - [Misc][Commercial] Moved NO OIL PRESSURE RISE failure to ATA 80 (Start Faults) - [Misc][Professional] Fixed crash at startup due to invalid tuning parameters Displays: - [PFD] Adjusted AH failed info - [PFD][APP DATA] Improved ILS course flag logic - [PFD][ALT TAPE] Fixed blue runway reference bar - [ND] Fixed VOR radial values - [ND] Fixed VOR radial showing inbound course in some conditions - [ND][VSD] Fixed EFIS RANGE 5 not working properly - [ND][PLAN] Fixed incorrect range - [ND][Terrain] Improved advanced terrain processing - [SEI] Moved engine indications to the left to align with upper DU gauges Jul 20 2021 Release Version 3.08 ====================================== System: Navigation - [FMS][VNAV] Added VNAV ALT cockpit setup option - [FMS][VNAV] Added MCP altitude capture inhibit Note: When in a LNAV/VNAV approach, it should be possible to select missed approach altitude in the MCP without reverting the pitch mode - [FMS][VNAV] Added deceleration segments Note: If required, VNAV will add a shallower deceleration segment to comply with speed restrictions - [FMS][VNAV] Added idle descent FPA adjustable for speed Note: Idle descend segment will be steeper for higher descend speeds and shallower for slower descend speeds. This will change the T/D location. - [FMS][VNAV] Added energy compensation program (beta) Note: If descending and in VNAV ALT, target speed will be adjusted to compensate for vertical deviation from the path - [FMS][VNAV] Added cockpit setup option to enable energy compensation - [FMS][VNAV] Added cockpit setup option to change VNAV speed descend thresholds Defaults are set to +15/-10. Possible values are [+|-][5|10|15] - [FMS][VNAV] Added (shallower) approach decel segment - [FMS][VNAV] Added cockpit setup option to enable gradual commanded speed (beta) Note: When a speed reduction is commanded by the VNAV, change will happen gradually. - [FMS][VNAV] VNAV PATH upper threshold exceedance logic revised to comply with FMS version Note: Not applicable to the NG. Part of the NG/MAX base FMS work. U14 will revert to SPD. Up to U13 will trigger DRAG REQUIRED and mode will remain on PATH - [FMS][VNAV] Allow engagement of VNAV during a G/A if above 400 RA - [FMS][VNAV] Reviewed early descent - [FMS][VNAV] Reviewed CRZ DES mode - [FMS][VNAV] Reviewed historic vnav speed - [FMS][VNAV] Do not command descend speed if near T/D and cruise speed is lower than descend speed - [FMS][VNAV] Fixed VNAV not remembering previous commanded speed if VNAV refreshed Note: When a change is made requiring VNAV to recalculate and A/C has a restricted speed, VNAV was not using previous cmd speed, but default one. - [FMS][VNAV] Fixed Thrust mode not reverting to MCP SPEED with SPD INT - [FMS][VNAV] Fixed ALT INT deleting all constraints during climb Note: When climbing, ALT INT was deleting all constraints for the entire route if MCP altitude above last climb restriction - [FMS][VNAV] Fixed VNAV not engaging in some conditions Note: When FMS is already in descend or approach phase, it is not possible to re-engage VNAV for a climb if aircraft is still before TOD. This can happen after a reposition. - [FMS][VNAV] Revised thrust mode for path descend - [FMS][VNAV] SPD INT should reset if VNAV SPD selected from CDU - [FMS][VNAV] SPD DES should revert to PATH DES when active leg has fixed FPA - [FMS][VNAV] Changing Common VNAV option should revert VNAV Note: Common VNAV option requires VNAV to be recycled to get proper logic. If changing this option, VNAV will revert to ALT HOLD/MCP SPD to force re-engagement. - [FMS][VNAV] Improved UNABLE CRUISE ALT message to verify climb/descent overlap situation - [FMS][VNAV] Improved vertical and thrust modes for descent to prevent flickering in some conditions - [FMS][VNAV] Fixed SPEED DES overshooting alt constraints - [FMS][VNAV] Fixed block altitude restriction Note: When a block altitude restriction was not complied, the lowest altitude value was used as target - [FMS][VNAV] Fixed VNAV mode when engaging below path - [FMS][VNAV] Fixed early descend - [FMS][VNAV] Fixed null exception when trying to engage VNAV from ALT HOLD - [FMS][VNAV] Fixed altitude restrictions when added to a SID waypoint after T/C - [FMS][VNAV] Fixed vnav speeds reference - [FMS][VNAV] Fixed SPD PATH change to levelling off if below path - [FMS][VNAV] Fixed VNAV DES SPEED thrust mode not always ARM - [FMS][VNAV] Fixed VNAV not acquiring constraint when in VNAV SPD DES mode - [FMS][VNAV] Fixed misplaced default decel marker - [FMS][VNAV] Fixed SPD INT not reverting to VNAV SPD - [FMS][VNAV] Fixed gradual CMD speed when flaps not up - [FMS][VNAV] Fixed locked commanded speed - [FMS][VNAV] Fixed flaps up speed commanded without DECEL marker - [FMS][VNAV] Fixed commanded speed not limited to flap speed while in cruise - [FMS][VNAV] Fixed TOO STEEP message for fixed GP legs - [FMS][VNAV] Fixed missed approach segment after G/A not having proper VNAV data Note: When performing a GA, T/D and DECEL markers were added if discontinuity is present after last waypoint - [FMS] Added "Common VNAV" cockpit setup option (beta) - [FMS] Added small margin to altitude difference when trying to engage VNAV already at cruise altitude - [FMS] Added cockpit setup option to change ALT INT mode [Delete all restrictions to MCP altitude | Delete first restriction only] Note: This option will change the behaviour of the ALT INT mode when deleting a restriction. Default is deleting all to MCP altitude. - [FMS][PROSIM737-112] Added "BUFFET ALERT" message - [FMS] Improved approach mode logic - [FMS] Improved G/A phase logic - [FMS] Revised G/A thrust mode - [FMS] Revised "CHECK FMC FUEL QUANTITY" message - [FMS] Revised ECON default speeds for lower flight levels - [FMS] Fixed invalid route when performing a GA - [FMS] Fixed calculation of altitude constraint waypoints not working until a/c reached 500 feet - [FMS] Fixed rounding issue with commanded speed - [FMS] Fixed "INSUFFICIENT FUEL" message - [FMS][PROSIM737-124] Fixed "USING RSV FUEL" message - [FMS] Fixed issue when PERF INIT data change causes VNAV to revert to ALT HOLD - [FMS] Fixed speed parser - [FMS] Fixed N1 value not retained when using N1 manual mode - [FMS] Fixed ALT INT deleting all restrictions in certain conditions - [FMS] Fixed CLB/CRZ/DES mode not reverting to ECON when CI is changed - [FMS] Fixed both CDU entering PLAN STEP mode when only one EFIS is in PLAN - [FMS] Fixed small issue with N1 output string format - [FMS] Fixed empty VNAV when no origin is entered Note: After a reposition, normally just the destination is entered. This was causing VNAV to be empty. - [FMS][IDENT][U13] Fixed CDU crash when companyroutes count is greater than 5 - [FMS][IDENT] Updated model to 737-800W for accuracy. SFP option will add .1 to AC model - [FMS][POS SHIFT] Fixed null exception when IRSes not aligned - [FMS][PERF INIT] Fixed TA modifying FMS - [FMS][PERF LIMITS] Fixed default speeds not restricted by perf limits Note: Manual target speeds are not affected by perf limits - [FMS][RTE] Improvements to company routes loading Note: It is possible now to load company route without clearing existing SID/STAR (if airports are the same) - [FMS][U13][RTE] Fixed RTE1/RTE2 mixed up ARR/DEP - [FMS][U13][RTE] Fixed RTE1/RTE2 CO RTE handler - [FMS][U13][RTE2] Fixed TAKE OFF speeds deleted when changing inactive route origin runway - [FMS][RTE] Fixed line not deleting when VIA has value and TO is empty - [FMS][U13][RTE2] Fixed CDU reset when trying to edit RTE2 segments - [FMS][U13][RTE2] Fixed RTE2 PLAN mode indexed to RTE1 - [FMS][LEGS] Improved PLAN CTR reset - [FMS][LEGS] Fixed magenta colour when MOD - [FMS][LEGS] Fixed first speed/alt restriction not magenta - [FMS][LEGS] Fixed dual disco in specific conditions Note: A dual disco was happening when selecting an APP/STAR before a SID, without any further waypoints in between. - [FMS][LEGS] Removed predicted speeds/altitudes and eta when leg is inactive missed approach - [FMS][LEGS] RTE data should only show or allow modification of wind for cruise legs - [FMS][LEGS] Fixed wind intensity formatting - [FMS][LEGS] Fixed winds populating backwards - [FMS][LEGS] Fixed speed/altitude restriction data entry - [FMS][LEGS] Fixed along track waypoints slightly off course - [FMS][LEGS] Fixed custom waypoint renaming when moved to top leg - [FMS][LEGS] Fixed PLAN STEP not going back to 1st page when reaching end of route - [FMS][DEP ARR][PAR-5584] Fixed ROUTE prompt not visible (LSK6R) for modified routes - [FMS][DEP ARR] Improved delay when selecting arrival - [FMS][ARR DEP] Fixed selection of ARR for origin not resetting destination data - [FMS][DEP ARR] Fixed ARR for origin showing departures - [FMS][CLB][DES] Fixed AT XXXXX if BLOCK altitude restriction - [FMS][CLB] Improved econ mode calculation - [FMS][CLB] Improved target speed logic - [FMS][CLB] Fixed cruise altitude visible and magenta when on cruise - [FMS][CLB] Fixed AT / ERR AT not using modified source - [FMS][CRZ] Improved econ mode calculation - [FMS][CRZ] Improved target speed logic - [FMS][CRZ] Fixed rounding issue with Cruise CAS speed - [FMS][DES] Implemented PATH/SPEED mode change - [FMS][DES] Speed/path prompt should not be visible if active leg has fixed FPA - [FMS][DES] Improved econ mode calculation - [FMS][DES] Improved target speed logic - [FMS][DES] Fixed null exception when EOD is invalid - [FMS][DES] Added speed to AT XXXXX (LSK1R) - [FMS][DES] Hide vertical deviation if less than 10 - [FMS][DES] Fixed target speed entry Note: When trying to enter mach, CAS value was deleted - [FMS][DES] Fixed WPT/ALT data entry Note: When not in descend phase, it should not be possible to enter WPT/ALT - [FMS][DES FORECAST] Improved T/D calculation to use descend winds first if populated Note: Idle descend segment will be adjusted for T/D wind from CRZ and DES FORECAST winds. - [FMS][DES FORECAST] Fixed TL modifying FMS - [FMS][APPROACH REF] Added cockpit setup option to allow vref speed entry on ground - [FMS][PROGRESS 1] Fixed ATA and FUEL when FROM waypoint is departing runway - [FMS][PROGRESS 1] Reworked fuel predictions - [FMS][PROGRESS 1] Fixed no fuel data in some conditions - [FMS][RTA][Commercial] RTA will only be avail with beta releases - [FMS][HOLD] Fixed decel marker for inactive missed approach segment Note: When a HOLD is present in an inactive missed approach segment, a speed decel marker should not be available - [FMS][HOLD] Fixed hold fuel calculation - [FMS][HOLD] Fixed EFC time not updating destination ETA - [FMS][HOLD] Fixed EFC not accounted for fuel prediction at destination - [FMS][HOLD] Fixed CDU crash when hold waypoint is after disco and last in route - [FMS][HOLD] Fixed MOD route not updating HOLD EXIT when armed - [FMS][HOLD] Prevent EFC data entry to be lower than ETA - [FMS][FIX] Fixed formatting issue when distance is more than 10 - [FMS][OFFSET] Fixed offset after DCT TO - [FMS][OFFSET] Improved calculation of start/exit waypoints when no data entered - [FMS][OFFSET] Changed entry from 30 to 45 degrees - [FMS][OFFSET] Fixed issue where OFFSET from PPOS triggers UNABLE OFFSET - [FMS][OFFSET] Fixed drawing issue when PPOS L offset entry does not fit in available distance to next waypoint - [FMS][OFFSET] Fixed leg index when calculating allowable offset entry distance - [FMS][OFFSET] Improved UNABLE OFFSET message logic - [FMS][OFFSET] Changed START WAYPOINT mandatory when offset from PPOS is not possible - [FMS][OFFSET] Fixed offset not happening if current leg is DF and start waypoint entered - [FMS][OFFSET] Added further validation to ppos offset to prevent drawing issues - [FMS][OFFSET] Fixed crash when doing offset after a direct to from a previous offset - [FMS][OFFSET] Fixed crash with ppos offset - [FMS][OFFSET] Fixed offset when no end leg is entered Note: Creating an offset without end leg, was causing the offset to reset - [FMS][OFFSET] Fixed offset when aircraft not on track - [FMS][OFFSET] improved offset validation due to internal offset model limitations - [FMS][OFFSET] Fixed lnav crashing when adding a PPOS offset - [FMS][OFFSET] Improved leg validation logic - [RNP] Fixed approach RNP mode Note: Fixes an issue when close to approach IF and above 3000ft, RNP mode was changing between ENR and APP. - [CDU] Auto switch to CLIMB page when executing a G/A Autoflight - [Autopilot] Revised VNAV law - [MCP] Added numerical test mode - [PROSIM737-116] Added source off to dual channel approach monitor - [AutoThrotle][Commercial] Fixed AT failure - [Autoflight] Fixed attempt to manual C/O if speed window is closed - [Autoflight] Fixed wrong commanded speed format when C/O pressed - [Autoflight] Fixed commanded mach exceeding MMO while descending - [Autoflight] Fixed autopilot CMD monitoring - [Autoflight] Small adjustment to GS capture mode - [Autoflight][Professional] Reviewed operational autoland annunciations - [Auto Throttle] Improved general FMC SPD / MCP SPD thrust control - [Auto Throttle] Improved FMC SPD / MCP SPD thrust modes to prevent overshooting of commanded speed while levelling off - [Auto Throttle] Fixed AT not working in some conditions Note: If Aspirated TAT is disabled and after an air reposition with an FMS reset, it is not possible to set OAT in N1 page. This fixe will allow AT to engage in this condition. Other - [Parking Brake] Revised release gate logic - [Fire Protection] Improved Engine Overheat failure with higher EGT indication - [Engines][Commercial] Added "No Oil Pressure Rise" failure - [Engines][Start Valve] Fixed valve not closing failure not having correct indications note: Indication should include a blinking, then remain illuminated. Just the blinking was happening. - [Equip Cooling] System overhaul - [Equip Cooling][Commercial] Added "Exhaust Equipment Cooling" failures - [CDS] Added CDS FAULT failure - [WXR Radar] Added option to select radar mode [Single | Dual] Default: Single Note: Select "Dual" if you have a split controls wxr radar panel. This will make left and right wxr radar sweep to be controlled independently. - [WXR Radar] Fixed ASN radar image not shown on display - [APU] Reworked ECU logic Note: LOW OIL PRESSURE will not trigger MC if APU not running. APU indicators will remain illuminated for 5 minutes after switch is in the OFF position. - [Hydraulics] Fixed system pressure to be 2700 with elec pumps only - [Electrical] Added GEN auto transfer when airborne Misc - [Engine failures][Commercial] Reviewed failures to have correct cockpit effects - [BITE] Fixed missing FQIS subsystem - [BITE] Fixed CDS ground tests crashing display instance - [FM] Improved flight model detection - [CompanyRoutes] Added capability to read companyroutes file from ProgramData\ProSim-AR\ProSimB738 folder - [ProSimIOS] Fixed overriding real-time Active Sky weather after position change - [ProSimIOS] Fixed some recording parameters could not be imported/exported - [SDK] Added aircraft.flightControls.trim.aileron.normalized and aircraft.flightControls.trim.rudder.normalized datarefs - [Misc] Renamed LE Flap extension scheme option to Short Field Package - [Misc] FMS reset now requires EXEC Note: Added to prevent accidental reset. - [Misc] Added cockpit setup option to select Thrust Mode Annunciation [Option 1|Option 2] Option 1 TO: [TO | TO 1 | TO 2 | D-TO | D-TO 1 | D-TO 2] CLB: [CLB | CLB 1 | CLB 2] Option 2 TO: [TO | R-TO] CLB: [CLB | R-CLB] - [Misc] Added cockpit setup option to enable the VNAV speed band on the ND - [Misc] Set default glide angle to 3 degrees Note: Older prosim flight models require a value between 2.6 and 2.7. P3D/FS2020 flight models require a 3.0 value. A new install will set this value to 3, but if updating from previous version requires the value to be checked and updated to 3 if using a P3D/FS2020 ProSim flight model. - [Misc] Fixed additional T/C marker when modifying route - [Misc] Fixed unit text size on several CDU pages - [Misc] Fixed rounding issue with CLB/DES CAS speeds - [Misc] Added CVR release gate Note: It will trip the CVR switch from ON to AUTO when any engine running - [Misc] Added cockpit setup option to show trim value on display trim indicator - [Misc] Improved LEGS DATA handling to prevent some parser issues with some CDU hardware Note: LEGS RTE DATA page when showing on the FSC CDU, the small Z from the ETA is in the wrong position - [Misc][PSDB-479] Added anti-collision light gate - [Misc][Commercial] Added alternate coordinate validation option to cockpit setup - [Misc] Fixed spurious LAND ALT flag during flight - [Misc] Improved course mismatch logic when virtual navaids option is disabled - [Misc] Fixed simulator Active Sky status no longer continuously refreshing without actual update Displays: - [ND] Fixed default decel segment markers - [ND] Fixed DECEL markers - [ND] Fixed CTE showing [L|R] when 0 - [ND] Fixed intercept route (dashed magenta) in some conditions - [ND] Fixed radial lines not properly drawn - [ND] Fixed DME signal when ILS is tuned - [PFD][Speed Tape][PSDB-482] Fixed V1 value not visible when off scale - [PFD][Speed Tape] Fixed speed band drawing in some cases - [PFD][SPEED TAPE] Improved speed trend vector shape - [PFD][SPEED TAPE] Fixed speed trend vector logic - [EICAS] Fixed SEI not popping up for high oil temperatures - [MCP] Fixed reversed VS mouse scroll and animation tuned - [MCP] Improved acceleration Drivers: - [CPFlight] Added split control mappings to new WXR RDR panel - [CPFlight] Fixed reverted switch inputs for new WXR panel - [CPFlight][PROSIM737-134] Added CVR mappings - [CPFlight] Fixed strobe & steady switch for the new ethernet overhead - [CPFlight] Fixed CAB/UTIL and IFE switches for the new ethernet overhead - [CPFlight][PAR-5283] Fixed ISFD altitude Note: If ISFD hardware is used, "Captain QNH controls FS QNH" and "Slave ISFD barometric setting to Capt EFIS" should be disabled - [Simworld][SW-82] Remove leading zeroes from ALT and VS displays - [FDS Ethernet] Refactored hardware detection Note: Advanced window was removed, and hardware implementation is based on device hostname. This will allow device PnP implementation within ProSim. May 28 2021 Release Version 3.07 ====================================== System: - [Commercial] Fixed engine start faults - [APU] Fixed APU quick start not working properly - [APU] Improved APU state logic - [Virtual Navaids] Fixed VOR signal - [Autopilot] Added cockpit setup option to select autopilot disengage warning mode - [Autopilot] Fixed Autopilot not disengaging with loss of hydraulics - [Autopilot] Fixed FLARE not becoming active at 50ft - [Landing Gear] Fixed gear working without hydraulics - [FMS][LNAV] Added single bypass for circle to track transition - [FMS] Improved "UNABLE NEXT ALTITUDE" message logic for descent constraints - [FMS][TakeOff] Reset V speeds at first flap retraction above accel height to prevent white bug(V2+[15|20]) to clear - [FMS][HOLD] When exit armed, ND should show just the holding exit without drawing the full hold - [EICAS][SYS] Fixed small rudder element misalignment - [EGPWS] Fixed crash when terrain elevation below 0 Displays: - [EGPWS][Terrain] Added option to change terrain mode [SIMPLE|ADVANCED] Note: Advanced (beta) contains the sweep and peaks options. Simple is the old logic - [EGPWS][Terrain] Added test image - [EGPWS][Terrain] Added terrain sweep - [EGPWS][Terrain] Added PEAKS option - [EGPWS][Terrain] Added water in CYAN option Drivers: - [EHID] Fixed TQ driver - [FDS] Fixed MCP G2 driver - [FSC TQ] Fixed parking brake release - [CPFlight] Added support for the new WXR radar panel - [CPFlight] Fixed GPWS INOP indicator not working - [CPFlight][Overhead] Fixed pressurization panel issue - [GoFlight] Fixed MCP/EFIS not working - [Simworld] Fixed ISFD baro encoder Misc: - [ProSimIOS] Shutdown all option now available also without any network computers configured - [Misc] Added support for digital outflow valve gauges - [Misc] Fixed ProSim crash when preparing for a second flight and FMS is not fully reset - [Misc] Improved navaid audio signal when aircraft is on ground - [Misc] Improved FD filter and interpolation Note: Old FD tuning parameters were replaced with 2 new parameters per channel: Time and Rate based. Apr 29 2021 Release Version 3.06 ====================================== System: - [Virtual Navaids] Fixed ident not working properly for VOR/ILS - [Virtual Navaids] Make sure ILS signal is always read from simulator to prevent scenery mismatches - [Virtual Navaids] Fixed ADF signal - [Virtual Navaids] Improved COM/NAV CDU page handling - [Virtual Navaids] Improved ILS approach data on PFD - [Virtual Navaids] Clear ILS cache when changing setting, to prevent restart for change to be effective - [FMS][HOLD] Fixed EFC modifying route - [FMS][VNAV] Added support for speed restrictions AT OR BELOW - [FMS][FIX] Extended radials - [FMS] Fixed CUTBACK - [FMS][FIX] Force RADIAL entry to have leading zeros - [FMS][APPROACH REF] Added leading zeros to ILS CRS - [FMS][LEGS] Improved text alignment - [FMS][LEGS] Fixed data entry allowed when no rte basic data entered (origin/departure) - [FMS][N1 LIMIT][PSDB-475] Fixed N1 header text missing data - [Commercial][PSDB-475] Added high oil temp failure - [EICAS][PSDB-475] Improved thrust mode annunciation - [Fire Protection][PROSIM737-67] Added wheel well fire Displays: - [EICAS] Improved N1 target caret - [EFIS] Improved amber barometric warning to also use mcp altitude value as reference - [ND] Fixed DME 0 in certain conditions - [ND] Small improvement to FIX RAD/DIS drawing lines - [ISFD] Fixed data flags - [ISFD] Fixed STD not working - [ISFD] Fixed STD not following capt EFIS when "Slave ISFD barometric setting to Capt EFIS" option is enabled - [ND][FIX RAD/DIST] Improved DIST value position - [ND][FIX RAD/DIST] Added radial value Drivers: - [Phidget22] Fixed Advance Servo not working - [PIM IRS] Fixed displays not showing normal data - [CPFlight][Overhead] Fixed LE devices mapping with usb version Misc: - [SDK] Added datarefs for generators amperes (aircraft.electrical.generator.[1|2|APU].ampere) - [ProSimIOS] Implemented new VATSIM data format to allow VATSIM information displayed on map again - [ProSimIOS] Fixed airspaces not shown on ProSimIOS map (needs new database build) - [Misc] Added new debug file Note: option can be found in WEB IOS/MAINT/MISC and it will create a debugLog.zip file containing log/crashlog files, config, sdk dump, vnav and lnav logs Apr 02 2021 Release Version 3.05 ====================================== - [FMS] Improved flight phase logic - [FMS][LNAV] Fixed LNAV intercept logic - [FMS][VNAV] Added "UNABLE NEXT ALTITUDE" FMC message - [FMS][POS INIT] Added missing LAST POS header on LSK1R - [FMS][PERF INIT] Improved GW output text - [FMS][PERF INIT] Improved CI output text - [FMS][PERF INIT] Improved ZFW output text - [FMS][PERF INIT] Improved RESERVES output text - [FMS][PERF INIT] Improved PLAN output text - [FMS][PERF INIT] Improved TRIP ALT logic - [FMS][PERF INIT] Improved FOB text output - [FMS][RTE] Fixed 0 course when waypoint is entered from RTE page - [FMS][TAKEOFF] Fixed CUTBACK select key - [FMS][TAKEOFF] Improved CG header text - [FMS][TAKEOFF] Improved RW SLOPE text output - [FMS][TAKEOFF] Fixed RW HDG deleting default value - [FMS][TAKEOFF] Fixed page not refreshing when manually setting speeds with MIP switch - [FMS][N1][TAKEOFF] Improved SEL/OAT text output - [FMS][N1] Fixed <###> markers alignment - [FMS][N1][TAKEOFF] Improved N1 text output - [FMS][LEGS] Fixed LEGS/RTE DATA change always going back to page 1 - [FMS][LEGS] Fixed along track waypoing not able to be added to INCT course leg when previous leg is discontinuity - [FMS][LEGS] Fixed along track waypoint when next leg is invalid - [FMS][LEGS] Fixed label overwriting text when in plan mode - [FMS][LEGS] Adjusted text when in STEP mode - [FMS][LEGS] Fixed empty speed/alt restriction text size - [FMS][LEGS] Fixed STEP TO jumping to invalid legs - [FMS][LEGS] Updated PLAN STEP to MAP CTR STEP text - [FMS][LEGS] Small improvement to Leg info (GP) - [FMS][CLB] Fixed missing ALT REST at LSK1R - [FMS][CLB] Added ERR AT at LSK3R - [FMS][CLB] Small improvement to ERR AT line - [FMS][CLB] Improved alt restriction logic - [FMS][DES] Improved alt restriction logic - [FMS][APPROACH REF] Improved page layout - [FMS][HOLD] Fixed hold entry when waypoint is not in route - [FMS][HOLD] Fixed HOLD AVAIL not showing - [FMS][PROGRESS 1] Fixed fuel predicions missing in certain conditions - [FMS][PROGRESS 1] Fixed TO waypoint DTG when route is MOD and TO waypoint is conditional waypoint - [FMS][PROGRESS 1] Improved layout - [FMS][PROGRESS 1] Fixed page not showing modified route - [FMS][PROGRESS 1] Fixed unit size - [FMS][PROGRESS 1] Fixed ATA and FUEL available when FROM is first point in route - [FMS][PROGRESS 1] Fixed next active waypoint color when name has a -(dash) - [FMS][PROGRESS 2] Fixed L/R showing when XTK is 0.00 - [FMS][FIX] Fixed decimal distance if entry is below 10NM - [FMS][FIX] Added dist from FIX decimal place - [FMS][FIX] Fixed rad/dis info when no PERF data is available - [FMS][FIX] Small display improvements - [FMS][OFFSET] Implemented new lnav offset logic - [ILS] Added indicator logic - [AUTOFLIGHT] Fixed lateral armed mode not reset when engaging HDG SEL - [DOORS] Added door control switch elements (Entry, Service and air stairs) - [APU] Added individual failures - [APU] Fixed indicators not remaining illuminated for 5 minutes Dysplays: - [ND] Fixed clipping - [ND] Added altitude restriction and ETA to PLAN mode - [ND] Fixed GS value alignment - [ND] Added missing degree symbol to wind when wind is not available - [ND] Fixed needle data not available if ILS tuned - [ND] Fixed empty ident text - [ND] Fixed reversed active VOR radial - [ND] Improved active VOR radial line - [ND] Fixed altitude restrictions always in feet - [ND] Fixed active waypoint not magenta - [PFD] Fixed barometric setting warning not using TL - [PFD] Fixed GS value alignment - [PFD] Fixed VR speed bug - [ISFD] Fixed alignment issues Drivers: - [Phidget22] Fixed crash when selecting HUB port already in use - [Phidget22] Fixed phidget already open when selecting hub port 0 device - [Phidget22] Several improvements - [CPFlight][MIP] Fixed N1 and REF speeds encoders not working - [CPFlight] Fixed swaped duct pressure needles for the new ethernet overhead - [CPFlight] Fixed swapped SOURCE OFF and GEN OFF BUS indicators (USB version) - [CPFlight] Added extra delay to bit indicator commands - [SIOC Direct] Added further encoder inputs based on mastercard count Misc: - [Maint][Doors] Improved readability - [Maint] Shutdown from CDU now requires EXEC - [ProSimAudio] fixed remote shutdown not working - [Misc] Added remote shutdown to system module - [Misc] Fixed issue causing flaps to be operated with no hydraulics, when simconnect is used as sim link - [Misc] Fixed EGT equals to OAT in some situations - [Misc] Fixed missing FMS version option - [CDU] Fixed DELETE key function when current page has no valid DELETE operation - [SPEED REF SWITCH] Fixed manual VREF Mar 04 2021 Release Version 3.04 ====================================== System: - [CDU] Fixed TAKE OFF page not accepting manual V SPEED value if single click option enabled - [FMS] Added CRZ CLB and CRZ DES modes - [FMS] Consolidated company route loading - [FMS][LEGS] Fixed double small text markup - [FMS][TAKEOFF] Improved Vspeeds reset when no route entered - [Warning] Fixed ELEC warning group not working Displays: - [PFD/ND] Fixed several elements misplaced - [EICAS] Small improvement to engine indicators - [EICAS] Fixed red line N2 value Drivers: - [CPFlight] Added new AFT overhead Misc: - [Misc] Fixed airstairs state with flight model version 1.55 Feb 05 2021 Release Version 3.03 ====================================== System: - [FMS] Fixed MCP altitude change not showing on scratchpad during cruise - [FMS][DES FORECAST] Fixed TL not populating when loading route from company route - [FMS][FIX] Fixed copy to scratchpad - [FMS][FIX] Fixed rad/dis accepting negative values - [FMS] Fixed STAR selection not clearing if no STAR segment in route - [FMS] Added further VNAV log - [FMS] Fixed ALT INT deleting E/D altitude restriction - [FMS] Fixed FC leg causing vnav distance errors - [FMS] Added OAT DISAGREE-DELETED message - [FMS] Added CHECK FMC FUEL QUANTITY message - [FMS][HOLD] Changed INVALID ENTRY to INVALID QUAD when trying to change the HOLD QUAD over a PBD waypoint - [FMS] Added ROUTE FULL message - [FMS][LEGS] Fixed CDU crash when entering HOLD at the end of the route - [FMS][LNAV] Fixed sequencing of manual legs (VECTOR) - [FMS][LEGS] Fixed CDU crash - [FMS][LEGS] Fixed selectable conditional waypoints - [FMS][POS] Fixed TA no filling when entering ref airport - [PSDB-469][FMS] Fixed FMS phase not changing from take off to climb after passing thrust reduction altitude - [PROSIM737-121][FMS][HOLD] Improved HOLD AVAIL calculation - [PROSIM737-122][FMS][CLB] Show proper CLB mode while on ground or take off phase - [FMS][VNAV] Initial speed predictions now takes into consideration acceleration height limit - [FMS] Fixed vnavDistance calculation taking matching fix to wrong flightplan waypoint if waypoint is also present in missed approach - [FMS][LEGS] Fixed RWY EXT renaming if DCT - [FMS][LEGS] Fixed extra disconnect when entering RWY EXT - [PROSIM737-118][FMS][TAKE OFF] Added option to use single click to select QRH speed - [FMS] Fixed VNAV not recalculating modified route - [ACARS] Fixed acars not loading remaining files if an acars file is invalid - [PROSIM737-120][Professional] Added inextinguishable fire failures - [PROSIM737-120][Professional] Added engine fire failures extinguishable with 2 bottles - Improved startup table Displays: - [PFD][SPEED TAPE] Fixed NO VSPDS flag also moving with speed - [ND][VSD] Fixed missing approach path - [ND] Fixed exclusions for wxr images in center mode - [ND] Fixed zoom factor in Center and Plan mode - [CPFlight] Added ethernet overhead support Note: This requires users with USB version to re-select COM port - [PFD] Fixed PLI shape for single cue FD Drivers: - [Phidget22] Fixed DigitalOutput for relays and indicators - [CPFlight] Fixed crash when using MAX EFIS - [CPFlight] Added MAX EFIS range support Misc: - [Flight Model] Added support for the flight model 1.55 airstairs - [Weather] Added support to exchange simulator weather information directly with Active Sky (enable in ProSimSystem config) - [ProSimIOS] Fixed VATSIM/IVAO/PilotEdge clients not shown on ProSimIOS map - [ProSimIOS] Fixed map buttons hiding based on window size now more reliable - [FS2020] Added community scenery import - [FS2020] Fixed database detection - [FS2020] Fixed engine data loading - [FS2020] Added FS2020 preview - [Misc] Added AirStairs control - [Misc] Added FMS/CDU->Flap Source option to cockpit setup This should be used when flaps control is done directly in the simulator and assigments cannot be done in ProSim (like old rev sim TQs). Default option is Handle, but if TQ is controlling simulator flaps directly (like the Rev SIm Script based TQ), then position should be used so VNAV can properly detect flap setting selected. - [Misc] Allow the use of custom sound files for default audio Note: To use custom default sounds (GPWS callouts, fire bell, clacker, etc...), just place the custom audio file(using the exact same name as the default one) inside the ProgramData\ProSim-AR\\audio foder. If the custom audio file is found, it will be used instead of the default one Jan 07 2021 Release Version 3.02 ====================================== System: - [FMS] Fixed along track waypoints when no active route - [PROSIM737-115][FMS][DES FORECAST] Fixed isa dev/qnh data entry parser - [FMS] Fixed VECTOR leg handling - [FMS][PROG1] Fixed leg direction - [FMS][LEGS] Fixed CDU crash when ARR/DEP avail but no legs yet - [FMS][CLB][CRZ][DES] Fixed CDU crash - [FMS][LEGS] Fixed 1st waypoint distance - [FMS][LEGS] Fixed non active route not showing direction and distance - [FMS] Improved VECTOR leg handling - [FMS] Fixed climb speed not reset after passing speed limit altitude - [FMS][RNP] Fixed rnp mode toggling between terminal and approach in certain conditions - [PFD][NPS] Fixed scale changing to ILS type as soon as ILS is tuned - [FMS][LEGS] Fixed single waypoint parser - [FMS][LEGS] Fixed INTC course when leg is entered at top - [Commercial][FMS][RTA] Added RTA functionality - [FMS][LEGS] Improved data entry parser - [FMS][PROGRESS 1] Fixed formatting when fuel is invalid - [PSDB-467][FMS][PROGRESS 1] Fixed DTG for next/after waypoints showing same value - [PSDB-466][FMS][CLB][CRZ][DES] Fixed target speed not showing XXX/MCP if speed intervention active - [AutoBrake] Manual brake input increased to 5% to prevent spurious system disarm - [ParkinBrake] Reworked system (due to future FS2020 compatibility) - [PSDB-468][FMA] Fixed thrust mode during take off - [MCP] Fixed SPEED mode not working properly when selected - [ADIRS] Split AoA signal Diplays: - [ND] Improved waypoint drawing (if same waypoint is present twice in route, just one will be drawing to prevent double drawing effect) - [PFD] Added Pitch and Roll flags - [PFD] Improved ATT flag - [PFD] Added AOA flag - [PSDB-465][Commercial] Fixed Start Valve Open blinking for more than 10 seconds if valve remains open Drivers: - [CPFlight] Implement SIDE module if MIPICS is detected - [CPFlight][CDUPRO] Fixed some parsing error Misc: - [Rudder/Tiller Combiner] Fixed auto detection not working with FSUIPC - [SimConnect] Fixed invalid approach data if no ILS active - [ProSimIOS] Fixed weight and temperature unit now also changed for the system side when changed in ProSimIOS - [Misc] Renamed MSFS simlink to FSUIPC to prevent confusion with the new MS FS2020 Dec 15 2020 Release Version 3.01 ====================================== System: - [FMS][FIX] Added rad/dist and abeam info (eta/dtg/alt) - [FMS][FIX] Improved rwy format entry - [FMS] Custom waypoints are now ODD numbered if generated from the Capt's CDU, and EVEN if from the FO's CDU - [FMS][IDENT] Simplified aircraft model - [FMS][MAIN-NAV/COM] Fixed ADF frequency not working - [FMS][VNAV] Added STEEP DES AFTER yyyyy message - [FMS][VNAV] Added UNABLE xxxKTS AT yyyyy message - [FMS][LEGS] Fixed ABEAM prompt visible in certain conditions - [Commercial][FMS][IDENT] Fixed StandBy cycle info - [Commercial][FMS][IDENT] Added optional operator code to cycle value - [Commercial][FMS][IDENT] Added custom model capability - [PSDB-464][FMS] Fixed company routes not persistent - [PSDB-461][FMS][DES] Fixed flap limit speed value - [Navigation][Marker] Fixed marker not resetting - [Commercial] Added oil quantity unit option to cockpit setup - [Navigation][ADF] Fixed min frequency from 200 to 190 Diplays: - [ProSimDisplay][EICAS] Fixed FF box size on upper EICAS - [ProSimDisplay][ND] Fixed altitude predicion line - [ProSimDisplay][ND] Fixed turn prediction - [ProSimDisplay][ND] Fixed missing track line Drivers: - [SIOC] Fixed EFIS mappings fro MCP based driver - [MCP][Drivers] Fixed FO efis switches not working - [CPFlight] Addes support to 80% MCP model - [CPFlight] Added suport for older MCPs - [FDS] Fixed MCP hold solenoid mapping - [Phidgets] Fixed config issue Misc: - [Misc] Fixed issue where navaids were always virtualized - [FlightModel] Add cockpit setup option to control doors from external source Note: enabling this option will remove any door control from ProSim, making IOS and CDU control pages to not respond. Indications will follow actual door state - [SDK] Fixed aircraft.fms.flightNumber dataref - [ProSimIOS] Added new program icon - [ProSimIOS] Fixed simulator weather no longer touched on start if enforce weather control setting is disabled - [ProSimIOS] Fixed connection to network client - [ACARS] Added legacy ACARS support - [SimConnect] Fixed incorrect oil qty - [SimConnect] Linked battery switch to simulator - [SimConnect] Fixed brakes not working - [Combined Rudder/Tiller] Fixed not working with MSFS(FSUIPC) simlink - [Rudder/Tiller Combiner] Added Rudder/Tiller mode detection. ProSim will determine now the proper mode to be use based on the inhibit_rudder_on_steer flag - [Rudder/Tiller Combiner] Removed option as it is no longer needed - [Rudder/Tiller Combiner] Added NWS control mode detected to WebIOS (Main/Parameters) - [Database] Fixed whole database build no longer aborts in case of a data record import error from the navigation data - [Database] Improved scan time - [Database] Fix loading airports in ProSim-System - [Database] Auto build database with new schema - [Database] Fix for null characters in scenery file data - [Database] Fixed weather station import - [Database] Improved Navaid Virtualization. Enabled by default. Note: For Non-Commercial users this is a new option, allowing the use of navdata to build navaid signals. instead of using the simulator navaid For commercial, and above, option was renamed from "Navdata Source" to "Virtual Navaids" Nov 13 2020 Release Version 3.00 ====================================== - First Release